board_enable.c

/*
 * This file is part of the flashrom project.
 *
 * Copyright (C) 2005-2007 coresystems GmbH <stepan@coresystems.de>
 * Copyright (C) 2006 Uwe Hermann <uwe@hermann-uwe.de>
 * Copyright (C) 2007-2009 Luc Verhaegen <libv@skynet.be>
 * Copyright (C) 2007 Carl-Daniel Hailfinger
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; version 2 of the License.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 */

/*
 * Contains the board specific flash enables.
 */

#include <strings.h>
#include <string.h>
#include <stdbool.h>
#include <stdlib.h>
#include "flash.h"
#include "programmer.h"
#include "hwaccess.h"

#if defined(__i386__) || defined(__x86_64__)
/*
 * Helper functions for many Winbond Super I/Os of the W836xx range.
 */
/* Enter extended functions */
void w836xx_ext_enter(uint16_t port)
{
	OUTB(0x87, port);
	OUTB(0x87, port);
}

/* Leave extended functions */
void w836xx_ext_leave(uint16_t port)
{
	OUTB(0xAA, port);
}

/* Generic Super I/O helper functions */
uint8_t sio_read(uint16_t port, uint8_t reg)
{
	OUTB(reg, port);
	return INB(port + 1);
}

void sio_write(uint16_t port, uint8_t reg, uint8_t data)
{
	OUTB(reg, port);
	OUTB(data, port + 1);
}

void sio_mask(uint16_t port, uint8_t reg, uint8_t data, uint8_t mask)
{
	uint8_t tmp;

	OUTB(reg, port);
	tmp = INB(port + 1) & ~mask;
	OUTB(tmp | (data & mask), port + 1);
}

/* Winbond W83697 documentation indicates that the index register has to be written for each access. */
static void sio_mask_alzheimer(uint16_t port, uint8_t reg, uint8_t data, uint8_t mask)
{
	uint8_t tmp;

	OUTB(reg, port);
	tmp = INB(port + 1) & ~mask;
	OUTB(reg, port);
	OUTB(tmp | (data & mask), port + 1);
}

/* Not used yet. */
#if 0
static int enable_flash_decode_superio(void)
{
	int ret;
	uint8_t tmp;

	switch (superio.vendor) {
	case SUPERIO_VENDOR_NONE:
		ret = -1;
		break;
	case SUPERIO_VENDOR_ITE:
		enter_conf_mode_ite(superio.port);
		/* Enable flash mapping. Works for most old ITE style Super I/O. */
		tmp = sio_read(superio.port, 0x24);
		tmp |= 0xfc;
		sio_write(superio.port, 0x24, tmp);
		exit_conf_mode_ite(superio.port);
		ret = 0;
		break;
	default:
		msg_pdbg("Unhandled Super I/O type!\n");
		ret = -1;
		break;
	}
	return ret;
}
#endif

/*
 * SMSC FDC37B787: Raise GPIO50
 */
static int fdc37b787_gpio50_raise(uint16_t port)
{
	uint8_t id, val;

	OUTB(0x55, port);	/* enter conf mode */
	id = sio_read(port, 0x20);
	if (id != 0x44) {
		msg_perr("\nERROR: FDC37B787: Wrong ID 0x%02X.\n", id);
		OUTB(0xAA, port); /* leave conf mode */
		return -1;
	}

	sio_write(port, 0x07, 0x08);	/* Select Aux I/O subdevice */

	val = sio_read(port, 0xC8);	/* GP50 */
	if ((val & 0x1B) != 0x10)	/* output, no invert, GPIO */
	{
		msg_perr("\nERROR: GPIO50 mode 0x%02X unexpected.\n", val);
		OUTB(0xAA, port);
		return -1;
	}

	sio_mask(port, 0xF9, 0x01, 0x01);

	OUTB(0xAA, port);		/* Leave conf mode */
	return 0;
}

/*
 * Suited for:
 *  - Nokia IP530: Intel 440BX + PIIX4 + FDC37B787
 */
static int fdc37b787_gpio50_raise_3f0(void)
{
	return fdc37b787_gpio50_raise(0x3f0);
}

struct winbond_mux {
	uint8_t reg;		/* 0 if the corresponding pin is not muxed */
	uint8_t data;		/* reg/data/mask may be directly ... */
	uint8_t mask;		/* ... passed to sio_mask */
};

struct winbond_port {
	const struct winbond_mux *mux; /* NULL or pointer to mux info for the 8 bits */
	uint8_t ldn;		/* LDN this GPIO register is located in */
	uint8_t enable_bit;	/* bit in 0x30 of that LDN to enable
	                           the GPIO port */
	uint8_t base;		/* base register in that LDN for the port */
};

struct winbond_chip {
	uint8_t device_id;	/* reg 0x20 of the expected w83626x */
	uint8_t gpio_port_count;
	const struct winbond_port *port;
};


#define UNIMPLEMENTED_PORT {NULL, 0, 0, 0}

enum winbond_id {
	WINBOND_W83627HF_ID = 0x52,
	WINBOND_W83627EHF_ID = 0x88,
	WINBOND_W83627THF_ID = 0x82,
	WINBOND_W83697HF_ID = 0x60,
};

static const struct winbond_mux w83627hf_port2_mux[8] = {
	{0x2A, 0x01, 0x01},	/* or MIDI */
	{0x2B, 0x80, 0x80},	/* or SPI */
	{0x2B, 0x40, 0x40},	/* or SPI */
	{0x2B, 0x20, 0x20},	/* or power LED */
	{0x2B, 0x10, 0x10},	/* or watchdog */
	{0x2B, 0x08, 0x08},	/* or infra red */
	{0x2B, 0x04, 0x04},	/* or infra red */
	{0x2B, 0x03, 0x03}	/* or IRQ1 input */
};

static const struct winbond_port w83627hf[3] = {
	UNIMPLEMENTED_PORT,
	{w83627hf_port2_mux, 0x08, 0, 0xF0},
	UNIMPLEMENTED_PORT,
};

static const struct winbond_mux w83627ehf_port2_mux[8] = {
	{0x29, 0x06, 0x02},	/* or MIDI */
	{0x29, 0x06, 0x02},
	{0x24, 0x02, 0x00},	/* or SPI ROM interface */
	{0x24, 0x02, 0x00},
	{0x2A, 0x01, 0x01},	/* or keyboard/mouse interface */
	{0x2A, 0x01, 0x01},
	{0x2A, 0x01, 0x01},
	{0x2A, 0x01, 0x01},
};

static const struct winbond_port w83627ehf[6] = {
	UNIMPLEMENTED_PORT,
	{w83627ehf_port2_mux, 0x09, 0, 0xE3},
	UNIMPLEMENTED_PORT,
	UNIMPLEMENTED_PORT,
	UNIMPLEMENTED_PORT,
	UNIMPLEMENTED_PORT,
};

static const struct winbond_mux w83627thf_port4_mux[8] = {
	{0x2D, 0x01, 0x01},	/* or watchdog or VID level strap */
	{0x2D, 0x02, 0x02},	/* or resume reset */
	{0x2D, 0x04, 0x04},	/* or S3 input */
	{0x2D, 0x08, 0x08},	/* or PSON# */
	{0x2D, 0x10, 0x10},	/* or PWROK */
	{0x2D, 0x20, 0x20},	/* or suspend LED */
	{0x2D, 0x40, 0x40},	/* or panel switch input */
	{0x2D, 0x80, 0x80},	/* or panel switch output */
};

static const struct winbond_port w83627thf[5] = {
	UNIMPLEMENTED_PORT,	/* GPIO1 */
	UNIMPLEMENTED_PORT,	/* GPIO2 */
	UNIMPLEMENTED_PORT,	/* GPIO3 */
	{w83627thf_port4_mux, 0x09, 1, 0xF4},
	UNIMPLEMENTED_PORT,	/* GPIO5 */
};

static const struct winbond_chip winbond_chips[] = {
	{WINBOND_W83627HF_ID,  ARRAY_SIZE(w83627hf),  w83627hf },
	{WINBOND_W83627EHF_ID, ARRAY_SIZE(w83627ehf), w83627ehf},
	{WINBOND_W83627THF_ID, ARRAY_SIZE(w83627thf), w83627thf},
};

#define WINBOND_SUPERIO_PORT1	0x2e
#define WINBOND_SUPERIO_PORT2	0x4e

/* We don't really care about the hardware monitor, but it offers better (more specific) device ID info than
 * the simple device ID in the normal configuration registers.
 * Note: This function expects to be called while the Super I/O is in config mode.
 */
static uint8_t w836xx_deviceid_hwmon(uint16_t sio_port)
{
	uint16_t hwmport;
	uint16_t hwm_vendorid;
	uint8_t hwm_deviceid;

	sio_write(sio_port, 0x07, 0x0b); /* Select LDN 0xb (HWM). */
	if ((sio_read(sio_port, 0x30) & (1 << 0)) != (1 << 0)) {
		msg_pinfo("W836xx hardware monitor disabled or does not exist.\n");
		return 0;
	}
	/* Get HWM base address (stored in LDN 0xb, index 0x60/0x61). */
	hwmport = sio_read(sio_port, 0x60) << 8;
	hwmport |= sio_read(sio_port, 0x61);
	/* HWM address register = HWM base address + 5. */
	hwmport += 5;
	msg_pdbg2("W836xx Hardware Monitor at port %04x\n", hwmport);
	/* FIXME: This busy check should happen before each HWM access. */
	if (INB(hwmport) & 0x80) {
		msg_pinfo("W836xx hardware monitor busy, ignoring it.\n");
		return 0;
	}
	/* Set HBACS=1. */
	sio_mask_alzheimer(hwmport, 0x4e, 0x80, 0x80);
	/* Read upper byte of vendor ID. */
	hwm_vendorid = sio_read(hwmport, 0x4f) << 8;
	/* Set HBACS=0. */
	sio_mask_alzheimer(hwmport, 0x4e, 0x00, 0x80);
	/* Read lower byte of vendor ID. */
	hwm_vendorid |= sio_read(hwmport, 0x4f);
	if (hwm_vendorid != 0x5ca3) {
		msg_pinfo("W836xx hardware monitor vendor ID weirdness: expected 0x5ca3, got %04x\n",
			  hwm_vendorid);
		return 0;
	}
	/* Set Bank=0. */
	sio_mask_alzheimer(hwmport, 0x4e, 0x00, 0x07);
	/* Read "chip" ID. We call this one the device ID. */
	hwm_deviceid = sio_read(hwmport, 0x58);
	return hwm_deviceid;
}

void probe_superio_winbond(void)
{
	struct superio s = {0};
	uint16_t winbond_ports[] = {WINBOND_SUPERIO_PORT1, WINBOND_SUPERIO_PORT2, 0};
	uint16_t *i = winbond_ports;
	uint8_t model;
	uint8_t tmp;

	s.vendor = SUPERIO_VENDOR_WINBOND;
	for (; *i; i++) {
		s.port = *i;
		/* If we're already in Super I/O config more, the W836xx enter sequence won't hurt. */
		w836xx_ext_enter(s.port);
		model = sio_read(s.port, 0x20);
		/* No response, no point leaving the config mode. */
		if (model == 0xff)
			continue;
		/* Try to leave config mode. If the ID register is still readable, it's not a Winbond chip. */
		w836xx_ext_leave(s.port);
		if (model == sio_read(s.port, 0x20)) {
			msg_pdbg("W836xx enter config mode worked or we were already in config mode. W836xx "
				 "leave config mode had no effect.\n");
			if (model == 0x87) {
				/* ITE IT8707F and IT8710F are special: They need the W837xx enter sequence,
				 * but they want the ITE exit sequence. Handle them here.
				 */
				tmp = sio_read(s.port, 0x21);
				switch (tmp) {
				case 0x07:
				case 0x10:
					s.vendor = SUPERIO_VENDOR_ITE;
					s.model = (0x87 << 8) | tmp ;
					msg_pdbg("Found ITE Super I/O, ID 0x%04hx on port "
						 "0x%x\n", s.model, s.port);
					register_superio(s);
					/* Exit ITE config mode. */
					exit_conf_mode_ite(s.port);
					/* Restore vendor for next loop iteration. */
					s.vendor = SUPERIO_VENDOR_WINBOND;
					continue;
				}
			}
			msg_pdbg("Active config mode, unknown reg 0x20 ID: %02x.\n", model);
			continue;
		}
		/* The Super I/O reacts to W836xx enter and exit config mode, it's probably Winbond. */
		w836xx_ext_enter(s.port);
		s.model = sio_read(s.port, 0x20);
		switch (s.model) {
		case WINBOND_W83627HF_ID:
		case WINBOND_W83627EHF_ID:
		case WINBOND_W83627THF_ID:
			msg_pdbg("Found Winbond Super I/O, id 0x%02hx\n", s.model);
			register_superio(s);
			break;
		case WINBOND_W83697HF_ID:
			/* This code is extremely paranoid. */
			tmp = sio_read(s.port, 0x26) & 0x40;
			if (((tmp == 0x00) && (s.port != WINBOND_SUPERIO_PORT1)) ||
			    ((tmp == 0x40) && (s.port != WINBOND_SUPERIO_PORT2))) {
				msg_pdbg("Winbond Super I/O probe weirdness: Port mismatch for ID "
					 "0x%02x at port 0x%04x\n", s.model, s.port);
				break;
			}
			tmp = w836xx_deviceid_hwmon(s.port);
			/* FIXME: This might be too paranoid... */
			if (!tmp) {
				msg_pdbg("Probably not a Winbond Super I/O\n");
				break;
			}
			if (tmp != s.model) {
				msg_pinfo("W83 series hardware monitor device ID weirdness: expected 0x%02x, "
					  "got 0x%02x\n", WINBOND_W83697HF_ID, tmp);
				break;
			}
			msg_pinfo("Found Winbond Super I/O, id 0x%02hx\n", s.model);
			register_superio(s);
			break;
		}
		w836xx_ext_leave(s.port);
	}
	return;
}

static const struct winbond_chip *winbond_superio_chipdef(void)
{
	int i;
	unsigned int j;

	for (i = 0; i < superio_count; i++) {
		if (superios[i].vendor != SUPERIO_VENDOR_WINBOND)
			continue;
		for (j = 0; j < ARRAY_SIZE(winbond_chips); j++)
			if (winbond_chips[j].device_id == superios[i].model)
				return &winbond_chips[j];
	}
	return NULL;
}

/*
 * The chipid parameter goes away as soon as we have Super I/O matching in the
 * board enable table. The call to winbond_superio_detect() goes away as
 * soon as we have generic Super I/O detection code.
 */
static int winbond_gpio_set(uint16_t base, enum winbond_id chipid,
                            int pin, int raise)
{
	const struct winbond_chip *chip = NULL;
	const struct winbond_port *gpio;
	int port = pin / 10;
	int bit = pin % 10;

	chip = winbond_superio_chipdef();
	if (!chip) {
		msg_perr("\nERROR: No supported Winbond Super I/O found\n");
		return -1;
	}
	if (chip->device_id != chipid) {
		msg_perr("\nERROR: Found Winbond chip with ID 0x%x, "
		         "expected %x\n", chip->device_id, chipid);
		return -1;
	}
	if (bit >= 8 || port == 0 || port > chip->gpio_port_count) {
		msg_perr("\nERROR: winbond_gpio_set: Invalid GPIO number %d\n",
		         pin);
		return -1;
	}

	gpio = &chip->port[port - 1];

	if (gpio->ldn == 0) {
		msg_perr("\nERROR: GPIO%d is not supported yet on this"
		          " winbond chip\n", port);
		return -1;
	}

	w836xx_ext_enter(base);

	/* Select logical device. */
	sio_write(base, 0x07, gpio->ldn);

	/* Activate logical device. */
	sio_mask(base, 0x30, 1 << gpio->enable_bit, 1 << gpio->enable_bit);

	/* Select GPIO function of that pin. */
	if (gpio->mux && gpio->mux[bit].reg)
		sio_mask(base, gpio->mux[bit].reg,
		         gpio->mux[bit].data, gpio->mux[bit].mask);

	sio_mask(base, gpio->base + 0, 0, 1 << bit);	/* Make pin output */
	sio_mask(base, gpio->base + 2, 0, 1 << bit);	/* Clear inversion */
	sio_mask(base, gpio->base + 1, raise << bit, 1 << bit);

	w836xx_ext_leave(base);

	return 0;
}

/*
 * Winbond W83627HF: Raise GPIO24.
 *
 * Suited for:
 *  - Agami Aruma
 *  - IWILL DK8-HTX
 */
static int w83627hf_gpio24_raise_2e(void)
{
	return winbond_gpio_set(0x2e, WINBOND_W83627HF_ID, 24, 1);
}

/*
 * Winbond W83627HF: Raise GPIO25.
 *
 * Suited for:
 *  - MSI MS-6577
 */
static int w83627hf_gpio25_raise_2e(void)
{
	return winbond_gpio_set(0x2e, WINBOND_W83627HF_ID, 25, 1);
}

/*
 * Winbond W83627EHF: Raise GPIO22.
 *
 * Suited for:
 *  - ASUS A8N-VM CSM: AMD Socket 939 + GeForce 6150 (C51) + MCP51
 */
static int w83627ehf_gpio22_raise_2e(void)
{
	return winbond_gpio_set(0x2e, WINBOND_W83627EHF_ID, 22, 1);
}

/*
 * Winbond W83627THF: Raise GPIO 44.
 *
 * Suited for:
 *  - MSI K8T Neo2-F V2.0
 */
static int w83627thf_gpio44_raise_2e(void)
{
	return winbond_gpio_set(0x2e, WINBOND_W83627THF_ID, 44, 1);
}

/*
 * Winbond W83627THF: Raise GPIO 44.
 *
 * Suited for:
 *  - MSI K8N Neo3
 */
static int w83627thf_gpio44_raise_4e(void)
{
	return winbond_gpio_set(0x4e, WINBOND_W83627THF_ID, 44, 1);
}

/*
 * Enable MEMW# and set ROM size to max.
 * Supported chips: W83L517D, W83697HF/F/HG, W83697SF/UF/UG
 */
static void w836xx_memw_enable(uint16_t port)
{
	w836xx_ext_enter(port);
	if (!(sio_read(port, 0x24) & 0x02)) {	/* Flash ROM enabled? */
		/* Enable MEMW# and set ROM size select to max. (4M). */
		sio_mask(port, 0x24, 0x28, 0x28);
	}
	w836xx_ext_leave(port);
}

/**
 * Enable MEMW# and set ROM size to max.
 * Supported chips:
 * W83697HF/F/HG, W83697SF/UF/UG
 */
static void w83697xx_memw_enable(uint16_t port)
{
	w836xx_ext_enter(port);
	if (!(sio_read(port, 0x24) & 0x02)) { /* Flash ROM enabled? */
		if((sio_read(port, 0x2A) & 0xF0) == 0xF0) {

		/* CR24 Bits 7 & 2 must be set to 0 enable the flash ROM    */
		/* address segments 000E0000h ~ 000FFFFFh on W83697SF/UF/UG */
		/* These bits are reserved on W83697HF/F/HG		    */
		/* Shouldn't be needed though.				    */

		/* CR28 Bit3 must be set to 1 to enable flash access to	    */
		/* FFE80000h ~ FFEFFFFFh on W83697SF/UF/UG.		    */
		/* This bit is reserved on W83697HF/F/HG which default to 0 */
			sio_mask(port, 0x28, 0x08, 0x08);

			/* Enable MEMW# and set ROM size select to max. (4M)*/
			sio_mask(port, 0x24, 0x28, 0x38);

		} else {
			msg_pwarn("Warning: Flash interface in use by GPIO!\n");
		}
	} else {
		msg_pinfo("BIOS ROM is disabled\n");
	}
	w836xx_ext_leave(port);
}

/*
 * Suited for:
 *  - Biostar M7VIQ: VIA KM266 + VT8235
 */
static int w83697xx_memw_enable_2e(void)
{
	w83697xx_memw_enable(0x2E);

	return 0;
}


/*
 * Suited for:
 *  - DFI AD77: VIA KT400 + VT8235 + W83697HF
 *  - EPoX EP-8K5A2: VIA KT333 + VT8235
 *  - Albatron PM266A Pro: VIA P4M266A + VT8235
 *  - Shuttle AK31 (all versions): VIA KT266 + VT8233
 *  - ASUS A7V8X-MX SE and A7V400-MX: AMD K7 + VIA KM400A + VT8235
 *  - Tyan S2498 (Tomcat K7M): AMD Geode NX + VIA KM400 + VT8237
 *  - MSI KM4M-V and KM4AM-V: VIA KM400/KM400A + VT8237
 *  - MSI MS-6561 (745 Ultra): SiS 745 + W83697HF
 *  - MSI MS-6787 (P4MAM-V/P4MAM-L): VIA P4M266 + VT8235
 *  - ASRock K7S41: SiS 741 + SiS 963 + W83697HF
 *  - ASRock K7S41GX: SiS 741GX + SiS 963L + W83697HF
 */
static int w836xx_memw_enable_2e(void)
{
	w836xx_memw_enable(0x2E);

	return 0;
}

/*
 * Suited for:
 *  - Termtek TK-3370 (rev. 2.5b)
 */
static int w836xx_memw_enable_4e(void)
{
	w836xx_memw_enable(0x4E);

	return 0;
}

/*
 * Suited for all boards with ITE IT8705F.
 * The SIS950 Super I/O probably requires a similar flash write enable.
 */
int it8705f_write_enable(uint8_t port)
{
	uint8_t tmp;
	int ret = 0;

	if (!(internal_buses_supported & BUS_PARALLEL))
		return 1;

	enter_conf_mode_ite(port);
	tmp = sio_read(port, 0x24);
	/* Check if at least one flash segment is enabled. */
	if (tmp & 0xf0) {
		/* The IT8705F will respond to LPC cycles and translate them. */
		internal_buses_supported &= BUS_PARALLEL;
		/* Flash ROM I/F Writes Enable */
		tmp |= 0x04;
		msg_pdbg("Enabling IT8705F flash ROM interface write.\n");
		if (tmp & 0x02) {
			/* The data sheet contradicts itself about max size. */
			max_rom_decode.parallel = 1024 * 1024;
			msg_pinfo("IT8705F with very unusual settings.\n"
				  "Please send the output of \"flashrom -V -p internal\" to\n"
				  "flashrom-stable@flashrom.org with \"IT8705: your board name: flashrom -V\"\n"
				  "as the subject to help us finish support for your Super I/O. Thanks.\n");
			ret = 1;
		} else if (tmp & 0x08) {
			max_rom_decode.parallel = 512 * 1024;
		} else {
			max_rom_decode.parallel = 256 * 1024;
		}
		/* Safety checks. The data sheet is unclear here: Segments 1+3
		 * overlap, no segment seems to cover top - 1MB to top - 512kB.
		 * We assume that certain combinations make no sense.
		 */
		if (((tmp & 0x02) && !(tmp & 0x08)) || /* 1 MB en, 512 kB dis */
		    (!(tmp & 0x10)) || /* 128 kB dis */
		    (!(tmp & 0x40))) { /*  256/512 kB dis */
			msg_perr("Inconsistent IT8705F decode size!\n");
			ret = 1;
		}
		if (sio_read(port, 0x25) != 0) {
			msg_perr("IT8705F flash data pins disabled!\n");
			ret = 1;
		}
		if (sio_read(port, 0x26) != 0) {
			msg_perr("IT8705F flash address pins 0-7 disabled!\n");
			ret = 1;
		}
		if (sio_read(port, 0x27) != 0) {
			msg_perr("IT8705F flash address pins 8-15 disabled!\n");
			ret = 1;
		}
		if ((sio_read(port, 0x29) & 0x10) != 0) {
			msg_perr("IT8705F flash write enable pin disabled!\n");
			ret = 1;
		}
		if ((sio_read(port, 0x29) & 0x08) != 0) {
			msg_perr("IT8705F flash chip select pin disabled!\n");
			ret = 1;
		}
		if ((sio_read(port, 0x29) & 0x04) != 0) {
			msg_perr("IT8705F flash read strobe pin disabled!\n");
			ret = 1;
		}
		if ((sio_read(port, 0x29) & 0x03) != 0) {
			msg_perr("IT8705F flash address pins 16-17 disabled!\n");
			/* Not really an error if you use flash chips smaller
			 * than 256 kByte, but such a configuration is unlikely.
			 */
			ret = 1;
		}
		msg_pdbg("Maximum IT8705F parallel flash decode size is %u.\n",
			max_rom_decode.parallel);
		if (ret) {
			msg_pinfo("Not enabling IT8705F flash write.\n");
		} else {
			sio_write(port, 0x24, tmp);
		}
	} else {
		msg_pdbg("No IT8705F flash segment enabled.\n");
		ret = 0;
	}
	exit_conf_mode_ite(port);

	return ret;
}

/*
 * The ITE IT8707F is a custom chip made by ITE exclusively for ASUS.
 * It uses the Winbond command sequence to enter extended configuration
 * mode and the ITE sequence to exit.
 *
 * Registers seems similar to the ones on ITE IT8710F.
 */
static int it8707f_write_enable(uint8_t port)
{
	uint8_t tmp;

	w836xx_ext_enter(port);

	/* Set bit 3 (GLB_REG_WE) of reg 0x23: Makes reg 0x24-0x2A rw */
	tmp = sio_read(port, 0x23);
	tmp |= (1 << 3);
	sio_write(port, 0x23, tmp);

	/* Set bit 2 (FLASH_WE) and bit 3 (FLASH_IF_EN) of reg 0x24 */
	tmp = sio_read(port, 0x24);
	tmp |= (1 << 2) | (1 << 3);
	sio_write(port, 0x24, tmp);

	/* Clear bit 3 (GLB_REG_WE) of reg 0x23: Makes reg 0x24-0x2A ro */
	tmp = sio_read(port, 0x23);
	tmp &= ~(1 << 3);
	sio_write(port, 0x23, tmp);

	exit_conf_mode_ite(port);

	return 0;
}

/*
 * Suited for:
 *  - ASUS P4SC-E: SiS 651 + 962 + ITE IT8707F
 */
static int it8707f_write_enable_2e(void)
{
	return it8707f_write_enable(0x2e);
}

#define PC87360_ID 0xE1
#define PC87364_ID 0xE4

static int pc8736x_gpio_set(uint8_t chipid, uint8_t gpio, int raise)
{
	static const int bankbase[] = {0, 4, 8, 10, 12};
	int gpio_bank = gpio / 8;
	int gpio_pin = gpio % 8;
	uint16_t baseport;
	uint8_t id, val;

	if (gpio_bank > 4) {
		msg_perr("PC8736x: Invalid GPIO %d\n", gpio);
		return -1;
	}

	id = sio_read(0x2E, 0x20);
	if (id != chipid) {
		msg_perr("PC8736x: unexpected ID %02x (expected %02x)\n",
			 id, chipid);
		return -1;
	}

	sio_write(0x2E, 0x07, 0x07);		/* Select GPIO device. */
	baseport = (sio_read(0x2E, 0x60) << 8) | sio_read(0x2E, 0x61);
	if ((baseport & 0xFFF0) == 0xFFF0 || baseport == 0) {
		msg_perr("PC87360: invalid GPIO base address %04x\n",
			 baseport);
		return -1;
	}
	sio_mask (0x2E, 0x30, 0x01, 0x01);	/* Enable logical device. */
	sio_write(0x2E, 0xF0, gpio_bank * 16 + gpio_pin);
	sio_mask (0x2E, 0xF1, 0x01, 0x01);	/* Make pin output. */

	val = INB(baseport + bankbase[gpio_bank]);
	if (raise)
		val |= 1 << gpio_pin;
	else
		val &= ~(1 << gpio_pin);
	OUTB(val, baseport + bankbase[gpio_bank]);

	return 0;
}

/*
 * VIA VT823x: Set one of the GPIO pins.
 */
static int via_vt823x_gpio_set(uint8_t gpio, int raise)
{
	struct pci_dev *dev;
	uint16_t base;
	uint8_t val, bit, offset;

	dev = pci_dev_find_vendorclass(0x1106, 0x0601);
	switch (dev->device_id) {
	case 0x3177:	/* VT8235 */
	case 0x3227:	/* VT8237/VT8237R */
	case 0x3337:	/* VT8237A */
		break;
	default:
		msg_perr("\nERROR: VT823x ISA bridge not found.\n");
		return -1;
	}

	if ((gpio >= 12) && (gpio <= 15)) {
		/* GPIO12-15 -> output */
		val = pci_read_byte(dev, 0xE4);
		val |= 0x10;
		pci_write_byte(dev, 0xE4, val);
	} else if (gpio == 9) {
		/* GPIO9 -> Output */
		val = pci_read_byte(dev, 0xE4);
		val |= 0x20;
		pci_write_byte(dev, 0xE4, val);
	} else if (gpio == 5) {
		val = pci_read_byte(dev, 0xE4);
		val |= 0x01;
		pci_write_byte(dev, 0xE4, val);
	} else {
		msg_perr("\nERROR: "
			"VT823x GPIO%02d is not implemented.\n", gpio);
		return -1;
	}

	/* We need the I/O Base Address for this board's flash enable. */
	base = pci_read_word(dev, 0x88) & 0xff80;

	offset = 0x4C + gpio / 8;
	bit = 0x01 << (gpio % 8);

	val = INB(base + offset);
	if (raise)
		val |= bit;
	else
		val &= ~bit;
	OUTB(val, base + offset);

	return 0;
}

/*
 * Suited for:
 *  - ASUS M2V-MX: VIA K8M890 + VT8237A + IT8716F
 */
static int via_vt823x_gpio5_raise(void)
{
	/* On M2V-MX: GPO5 is connected to WP# and TBL#. */
	return via_vt823x_gpio_set(5, 1);
}

/*
 * Suited for:
 *  - VIA EPIA EK & N & NL
 */
static int via_vt823x_gpio9_raise(void)
{
	return via_vt823x_gpio_set(9, 1);
}

/*
 * Suited for:
 *  - VIA EPIA M and MII (and maybe other CLE266 based EPIAs)
 *
 * We don't need to do this for EPIA M when using coreboot, GPIO15 is never
 * lowered there.
 */
static int via_vt823x_gpio15_raise(void)
{
	return via_vt823x_gpio_set(15, 1);
}

/*
 * Winbond W83697HF Super I/O + VIA VT8235 southbridge
 *
 * Suited for:
 *  - MSI KT4V and KT4V-L: AMD K7 + VIA KT400 + VT8235
 *  - MSI KT4 Ultra: AMD K7 + VIA KT400 + VT8235
 */
static int board_msi_kt4v(void)
{
	int ret;

	ret = via_vt823x_gpio_set(12, 1);
	w836xx_memw_enable(0x2E);

	return ret;
}

/*
 * Suited for:
 *  - ASUS P3B-F
 *
 * We are talking to a proprietary device on SMBus: the AS99127F which does
 * much more than the Winbond W83781D it tries to be compatible with.
 */
static int board_asus_p3b_f(void)
{
	/*
	 * Find where the SMBus host is. ASUS sets it to 0xE800; coreboot sets it to 0x0F00.
	 */
	struct pci_dev *dev;
	uint16_t smbba;
	uint8_t b;

	dev = pci_dev_find(0x8086, 0x7113); /* Intel PIIX4, PM/SMBus function. */
	if (!dev) {
		msg_perr("\nERROR: Intel PIIX4 PM not found.\n");
		return -1;
	}

	smbba = pci_read_word(dev, 0x90) & 0xfff0;

	OUTB(0xFF, smbba); /* Clear previous SMBus status. */
	OUTB(0x48 << 1, smbba + 4);
	OUTB(0x80, smbba + 3);
	OUTB(0x80, smbba + 5);
	OUTB(0x48, smbba + 2);

	/* Wait until SMBus transaction is complete. */
	b = 0x1;
	while (b & 0x01) {
		INB(0x80);
		b = INB(smbba);
	}

	/* Write failed if any status is set. */
	if (b & 0x1e) {
		msg_perr("Failed to write to device.\n");
		return -1;
	}

	return 0;
}

/*
 * Suited for:
 *  - ASUS P5A
 *
 * This is rather nasty code, but there's no way to do this cleanly.
 * We're basically talking to some unknown device on SMBus, my guess
 * is that it is the Winbond W83781D that lives near the DIP BIOS.
 */
static int board_asus_p5a(void)
{
	uint8_t tmp;
	int i;

#define ASUSP5A_LOOP 5000

	OUTB(0x00, 0xE807);
	OUTB(0xEF, 0xE803);

	OUTB(0xFF, 0xE800);

	for (i = 0; i < ASUSP5A_LOOP; i++) {
		OUTB(0xE1, 0xFF);
		if (INB(0xE800) & 0x04)
			break;
	}

	if (i == ASUSP5A_LOOP) {
		msg_perr("Unable to contact device.\n");
		return -1;
	}

	OUTB(0x20, 0xE801);
	OUTB(0x20, 0xE1);

	OUTB(0xFF, 0xE802);

	for (i = 0; i < ASUSP5A_LOOP; i++) {
		tmp = INB(0xE800);
		if (tmp & 0x70)
			break;
	}

	if ((i == ASUSP5A_LOOP) || !(tmp & 0x10)) {
		msg_perr("Failed to read device.\n");
		return -1;
	}

	tmp = INB(0xE804);
	tmp &= ~0x02;

	OUTB(0x00, 0xE807);
	OUTB(0xEE, 0xE803);

	OUTB(tmp, 0xE804);

	OUTB(0xFF, 0xE800);
	OUTB(0xE1, 0xFF);

	OUTB(0x20, 0xE801);
	OUTB(0x20, 0xE1);

	OUTB(0xFF, 0xE802);

	for (i = 0; i < ASUSP5A_LOOP; i++) {
		tmp = INB(0xE800);
		if (tmp & 0x70)
			break;
	}

	if ((i == ASUSP5A_LOOP) || !(tmp & 0x10)) {
		msg_perr("Failed to write to device.\n");
		return -1;
	}

	return 0;
}

/*
 * Set GPIO lines in the Broadcom HT-1000 southbridge.
 *
 * It's not a Super I/O but it uses the same index/data port method.
 */
static int board_hp_dl145_g3_enable(void)
{
	/* GPIO 0 reg from PM regs */
	/* Set GPIO 2 and 5 high, connected to flash WP# and TBL# pins. */
	sio_mask(0xcd6, 0x44, 0x24, 0x24);

	return 0;
}

/*
 * Set GPIO lines in the Broadcom HT-1000 southbridge.
 *
 * It's not a Super I/O but it uses the same index/data port method.
 */
static int board_hp_dl165_g6_enable(void)
{
	/* Variant of DL145, with slightly different pin placement. */
	sio_mask(0xcd6, 0x44, 0x80, 0x80); /* TBL# */
	sio_mask(0xcd6, 0x46, 0x04, 0x04); /* WP# */

	return 0;
}

static int board_ibm_x3455(void)
{
	/* Raise GPIO13. */
	sio_mask(0xcd6, 0x45, 0x20, 0x20);

	return 0;
}

/*
 * Suited for:
 * - Elitegroup GeForce6100SM-M: NVIDIA MCP61 + ITE IT8726F
 */
static int board_ecs_geforce6100sm_m(void)
{
	struct pci_dev *dev;
	uint32_t tmp;

	dev = pci_dev_find(0x10DE, 0x03EB);     /* NVIDIA MCP61 SMBus. */
	if (!dev) {
		msg_perr("\nERROR: NVIDIA MCP61 SMBus not found.\n");
		return -1;
	}

	tmp = pci_read_byte(dev, 0xE0);
	tmp &= ~(1 << 3);
	pci_write_byte(dev, 0xE0, tmp);

	return 0;
}

/*
 * Very similar to AMD 8111 IO Hub.
 */
static int nvidia_mcp_gpio_set(int gpio, int raise)
{
	struct pci_dev *dev;
	uint16_t base, devclass;
	uint8_t tmp;

	if ((gpio < 0) || (gpio >= 0x40)) {
		msg_perr("\nERROR: unsupported GPIO: %d.\n", gpio);
		return -1;
	}

	/* Check for the ISA bridge first. */
	dev = pci_dev_find_vendorclass(0x10DE, 0x0601);
	switch (dev->device_id) {
	case 0x0030: /* CK804 */
	case 0x0050: /* MCP04 */
	case 0x0060: /* MCP2 */
	case 0x00E0: /* CK8 */
		break;
	case 0x0260: /* MCP51 */
	case 0x0261: /* MCP51 */
	case 0x0360: /* MCP55 */
	case 0x0364: /* MCP55 */
		/* find SMBus controller on *this* southbridge */
		/* The infamous Tyan S2915-E has two south bridges; they are
		   easily told apart from each other by the class of the
		   LPC bridge, but have the same SMBus bridge IDs */
		if (dev->func != 0) {
			msg_perr("MCP LPC bridge at unexpected function"
			         " number %d\n", dev->func);
			return -1;
		}

#if !defined(OLD_PCI_GET_DEV)
		dev = pci_get_dev(pacc, dev->domain, dev->bus, dev->dev, 1);
#else
		/* pciutils/libpci before version 2.2 is too old to support
		 * PCI domains. Such old machines usually don't have domains
		 * besides domain 0, so this is not a problem.
		 */
		dev = pci_get_dev(pacc, dev->bus, dev->dev, 1);
#endif
		if (!dev) {
			msg_perr("MCP SMBus controller could not be found\n");
			return -1;
		}
		devclass = pci_read_word(dev, PCI_CLASS_DEVICE);
		if (devclass != 0x0C05) {
			msg_perr("Unexpected device class %04x for SMBus"
			         " controller\n", devclass);
			return -1;
		}
		break;
	default:
		msg_perr("\nERROR: no NVIDIA LPC/SMBus controller found.\n");
		return -1;
	}

	base = pci_read_long(dev, 0x64) & 0x0000FF00; /* System control area */
	base += 0xC0;

	tmp = INB(base + gpio);
	tmp &= ~0x0F; /* null lower nibble */
	tmp |= 0x04; /* gpio -> output. */
	if (raise)
		tmp |= 0x01;
	OUTB(tmp, base + gpio);

	return 0;
}

/*
 * Suited for:
 *  - ASUS A8M2N-LA (HP OEM "NodusM3-GL8E"): NVIDIA MCP51
 *  - ASUS A8N-LA (HP OEM "Nagami-GL8E"): NVIDIA MCP51
 *  - ASUS M2NBP-VM CSM: NVIDIA MCP51
 */
static int nvidia_mcp_gpio0_raise(void)
{
	return nvidia_mcp_gpio_set(0x00, 1);
}

/*
 * Suited for:
 *  - abit KN8 Ultra: NVIDIA CK804
 *  - abit KN9 Ultra: NVIDIA MCP55
 */
static int nvidia_mcp_gpio2_lower(void)
{
	return nvidia_mcp_gpio_set(0x02, 0);
}

/*
 * Suited for:
 *  - Foxconn 6150K8MD-8EKRSH: Socket 939 + NVIDIA MCP51
 *  - MSI K8N Neo4(-F/-FI/-FX/Platinum): NVIDIA CK804
 *  - MSI K8NGM2-L: NVIDIA MCP51
 *  - MSI K9N SLI: NVIDIA MCP55
 */
static int nvidia_mcp_gpio2_raise(void)
{
	return nvidia_mcp_gpio_set(0x02, 1);
}

/*
 * Suited for:
 *  - EPoX EP-8NPA7I: Socket 754 + NVIDIA nForce4 4X
 */
static int nvidia_mcp_gpio4_raise(void)
{
	return nvidia_mcp_gpio_set(0x04, 1);
}

/*
 * Suited for:
 *  - HP xw9400 (Tyan S2915-E OEM): Dual(!) NVIDIA MCP55
 *
 * Notes: a) There are two MCP55 chips, so also two SMBus bridges on that
 *           board. We can't tell the SMBus logical devices apart, but we
 *           can tell the LPC bridge functions apart.
 *           We need to choose the SMBus bridge next to the LPC bridge with
 *           ID 0x364 and the "LPC bridge" class.
 *        b) #TBL is hardwired on that board to a pull-down. It can be
 *           overridden by connecting the two solder points next to F2.
 */
static int nvidia_mcp_gpio5_raise(void)
{
	return nvidia_mcp_gpio_set(0x05, 1);
}

/*
 * Suited for:
 *  - abit NF7-S: NVIDIA CK804
 */
static int nvidia_mcp_gpio8_raise(void)
{
	return nvidia_mcp_gpio_set(0x08, 1);
}

/*
 * Suited for:
 *  - GIGABYTE GA-K8NS Pro-939: Socket 939 + NVIDIA nForce3  + CK8
 *  - Probably other versions of the GA-K8NS
 */
static int nvidia_mcp_gpio0a_raise(void)
{
	return nvidia_mcp_gpio_set(0x0a, 1);
}

/*
 * Suited for:
 *  - MSI K8N Neo Platinum: Socket 754 + nForce3 Ultra + CK8
 *  - MSI K8N Neo2 Platinum: Socket 939 + nForce3 Ultra + CK8
 */
static int nvidia_mcp_gpio0c_raise(void)
{
	return nvidia_mcp_gpio_set(0x0c, 1);
}

/*
 * Suited for:
 *  - abit NF-M2 nView: Socket AM2 + NVIDIA MCP51
 */
static int nvidia_mcp_gpio4_lower(void)
{
	return nvidia_mcp_gpio_set(0x04, 0);
}

/*
 * Suited for:
 *  - ASUS P5ND2-SLI Deluxe: LGA775 + nForce4 SLI + MCP04
 */
static int nvidia_mcp_gpio10_raise(void)
{
	return nvidia_mcp_gpio_set(0x10, 1);
}

/*
 * Suited for:
 *  - GIGABYTE GA-K8N-SLI: AMD socket 939 + NVIDIA CK804 + ITE IT8712F
 */
static int nvidia_mcp_gpio21_raise(void)
{
	return nvidia_mcp_gpio_set(0x21, 0x01);
}

/*
 * Suited for:
 *  - EPoX EP-8RDA3+: Socket A + nForce2 Ultra 400 + MCP2
 */
static int nvidia_mcp_gpio31_raise(void)
{
	return nvidia_mcp_gpio_set(0x31, 0x01);
}

/*
 * Suited for:
 *  - GIGABYTE GA-K8N51GMF: Socket 754 + Geforce 6100 + MCP51
 *  - GIGABYTE GA-K8N51GMF-9: Socket 939 + Geforce 6100 + MCP51
 */
static int nvidia_mcp_gpio3b_raise(void)
{
	return nvidia_mcp_gpio_set(0x3b, 1);
}

/*
 * Suited for:
 *  - Sun Ultra 40 M2: Dual Socket F (1207) + MCP55
 */
static int board_sun_ultra_40_m2(void)
{
	int ret;
	uint8_t reg;
	uint16_t base;
	struct pci_dev *dev;

	ret = nvidia_mcp_gpio4_lower();
	if (ret)
		return ret;

	dev = pci_dev_find(0x10de, 0x0364); /* NVIDIA MCP55 LPC bridge */
	if (!dev) {
		msg_perr("\nERROR: NVIDIA MCP55 LPC bridge not found.\n");
		return -1;
	}

	base = pci_read_word(dev, 0xb4); /* some IO BAR? */
	if (!base)
		return -1;

	reg = INB(base + 0x4b);
	reg |= 0x10;
	OUTB(reg, base + 0x4b);

	return 0;
}

/*
 * Suited for:
 *  - Artec Group DBE61 and DBE62
 */
static int board_artecgroup_dbe6x(void)
{
#define DBE6x_MSR_DIVIL_BALL_OPTS	0x51400015
#define DBE6x_PRI_BOOT_LOC_SHIFT	2
#define DBE6x_BOOT_OP_LATCHED_SHIFT	8
#define DBE6x_SEC_BOOT_LOC_SHIFT	10
#define DBE6x_PRI_BOOT_LOC		(3 << DBE6x_PRI_BOOT_LOC_SHIFT)
#define DBE6x_BOOT_OP_LATCHED		(3 << DBE6x_BOOT_OP_LATCHED_SHIFT)
#define DBE6x_SEC_BOOT_LOC		(3 << DBE6x_SEC_BOOT_LOC_SHIFT)
#define DBE6x_BOOT_LOC_FLASH		2
#define DBE6x_BOOT_LOC_FWHUB		3

	msr_t msr;
	unsigned long boot_loc;

	/* Geode only has a single core */
	if (setup_cpu_msr(0))
		return -1;

	msr = rdmsr(DBE6x_MSR_DIVIL_BALL_OPTS);

	if ((msr.lo & (DBE6x_BOOT_OP_LATCHED)) ==
	    (DBE6x_BOOT_LOC_FWHUB << DBE6x_BOOT_OP_LATCHED_SHIFT))
		boot_loc = DBE6x_BOOT_LOC_FWHUB;
	else
		boot_loc = DBE6x_BOOT_LOC_FLASH;

	msr.lo &= ~(DBE6x_PRI_BOOT_LOC | DBE6x_SEC_BOOT_LOC);
	msr.lo |= ((boot_loc << DBE6x_PRI_BOOT_LOC_SHIFT) |
		   (boot_loc << DBE6x_SEC_BOOT_LOC_SHIFT));

	wrmsr(DBE6x_MSR_DIVIL_BALL_OPTS, msr);

	cleanup_cpu_msr();

	return 0;
}

/*
 * Suited for:
 *  - ASUS A8AE-LE (Codename AmberineM; used in Compaq Presario 061)
 * Datasheet(s) used:
 *  - AMD document 43009 "AMD SB700/710/750 Register Reference Guide" rev. 1.00
 */
static int amd_sbxxx_gpio9_raise(void)
{
	struct pci_dev *dev;
	uint32_t reg;

	dev = pci_dev_find(0x1002, 0x4372); /* AMD SMBus controller */
	if (!dev) {
		msg_perr("\nERROR: AMD SMBus Controller (0x4372) not found.\n");
		return -1;
	}

	reg = pci_read_long(dev, 0xA8); /* GPIO_12_to_4_Cntrl CI_Reg: A8h-ABh */
	/* enable output (0: enable, 1: tristate):
	   GPIO9 output enable is at bit 5 in 0xA9 */
	reg &= ~((uint32_t)1<<(8+5));
	/* raise:
	   GPIO9 output register is at bit 5 in 0xA8 */
	reg |= (1<<5);
	pci_write_long(dev, 0xA8, reg);

	return 0;
}

/*
 * Helper function to raise/drop a given gpo line on Intel PIIX4{,E,M}.
 */
static int intel_piix4_gpo_set(unsigned int gpo, int raise)
{
	unsigned int gpo_byte, gpo_bit;
	struct pci_dev *dev;
	uint32_t tmp, base;

	/* GPO{0,8,27,28,30} are always available. */
	static const uint32_t nonmuxed_gpos = 0x58000101;

	static const struct {unsigned int reg, mask, value; } piix4_gpo[] = {
		{0},
		{0xB0, 0x0001, 0x0000},        /* GPO1... */
		{0xB0, 0x0001, 0x0000},
		{0xB0, 0x0001, 0x0000},
		{0xB0, 0x0001, 0x0000},
		{0xB0, 0x0001, 0x0000},
		{0xB0, 0x0001, 0x0000},
		{0xB0, 0x0001, 0x0000},        /* ...GPO7: GENCFG bit 0 */
		{0},
		{0xB0, 0x0100, 0x0000},        /* GPO9:  GENCFG bit 8 */
		{0xB0, 0x0200, 0x0000},        /* GPO10: GENCFG bit 9 */
		{0xB0, 0x0400, 0x0000},        /* GPO11: GENCFG bit 10 */
		{0x4E, 0x0100, 0x0000},        /* GPO12... */
		{0x4E, 0x0100, 0x0000},
		{0x4E, 0x0100, 0x0000},        /* ...GPO14: XBCS bit 8 */
		{0xB2, 0x0002, 0x0002},        /* GPO15... */
		{0xB2, 0x0002, 0x0002},        /* ...GPO16: GENCFG bit 17 */
		{0xB2, 0x0004, 0x0004},        /* GPO17: GENCFG bit 18 */
		{0xB2, 0x0008, 0x0008},        /* GPO18: GENCFG bit 19 */
		{0xB2, 0x0010, 0x0010},        /* GPO19: GENCFG bit 20 */
		{0xB2, 0x0020, 0x0020},        /* GPO20: GENCFG bit 21 */
		{0xB2, 0x0040, 0x0040},        /* GPO21: GENCFG bit 22 */
		{0xB2, 0x1000, 0x1000},        /* GPO22... */
		{0xB2, 0x1000, 0x1000},        /* ...GPO23: GENCFG bit 28 */
		{0xB2, 0x2000, 0x2000},        /* GPO24: GENCFG bit 29 */
		{0xB2, 0x4000, 0x4000},        /* GPO25: GENCFG bit 30 */
		{0xB2, 0x8000, 0x8000},        /* GPO26: GENCFG bit 31 */
		{0},
		{0},
		{0x4E, 0x0100, 0x0000},        /* ...GPO29: XBCS bit 8 */
		{0}
	};

	dev = pci_dev_find(0x8086, 0x7110);	/* Intel PIIX4 ISA bridge */
	if (!dev) {
		msg_perr("\nERROR: Intel PIIX4 ISA bridge not found.\n");
		return -1;
	}

	/* Sanity check. */
	if (gpo > 30) {
		msg_perr("\nERROR: Intel PIIX4 has no GPO%d.\n", gpo);
		return -1;
	}

	if ((((1 << gpo) & nonmuxed_gpos) == 0) &&
	    ((pci_read_word(dev, piix4_gpo[gpo].reg) & piix4_gpo[gpo].mask) !=
	     piix4_gpo[gpo].value)) {
		msg_perr("\nERROR: PIIX4 GPO%d not programmed for output.\n", gpo);
		return -1;
	}

	dev = pci_dev_find(0x8086, 0x7113);	/* Intel PIIX4 PM */
	if (!dev) {
		msg_perr("\nERROR: Intel PIIX4 PM not found.\n");
		return -1;
	}

	/* PM IO base */
	base = pci_read_long(dev, 0x40) & 0x0000FFC0;

	gpo_byte = gpo >> 3;
	gpo_bit = gpo & 7;
	tmp = INB(base + 0x34 + gpo_byte); /* GPO register */
	if (raise)
		tmp |= 0x01 << gpo_bit;
	else
		tmp &= ~(0x01 << gpo_bit);
	OUTB(tmp, base + 0x34 + gpo_byte);

	return 0;
}

/*
 * Suited for:
 *  - ASUS OPLX-M
 *  - ASUS P2B-N
 */
static int intel_piix4_gpo18_lower(void)
{
	return intel_piix4_gpo_set(18, 0);
}

/*
 * Suited for:
 *  - MSI MS-6163 v2 (MS-6163 Pro): Intel 440BX + PIIX4E + Winbond W83977EF
 */
static int intel_piix4_gpo14_raise(void)
{
	return intel_piix4_gpo_set(14, 1);
}

/*
 * Suited for:
 *  - EPoX EP-BX3
 */
static int intel_piix4_gpo22_raise(void)
{
	return intel_piix4_gpo_set(22, 1);
}

/*
 * Suited for:
 *  - abit BM6
 */
static int intel_piix4_gpo26_lower(void)
{
	return intel_piix4_gpo_set(26, 0);
}

/*
 * Suited for:
 *  - Intel SE440BX-2
 */
static int intel_piix4_gpo27_lower(void)
{
	return intel_piix4_gpo_set(27, 0);
}

/*
 * Suited for:
 *  - Dell OptiPlex GX1
 */
static int intel_piix4_gpo30_lower(void)
{
	return intel_piix4_gpo_set(30, 0);
}

/*
 * Set a GPIO line on a given Intel ICH LPC controller.
 */
static int intel_ich_gpio_set(int gpio, int raise)
{
	/* Table mapping the different Intel ICH LPC chipsets. */
	static struct {
		uint16_t id;
		uint8_t base_reg;
		uint32_t bank0;
		uint32_t bank1;
		uint32_t bank2;
	} intel_ich_gpio_table[] = {
		{0x2410, 0x58, 0x0FE30000,          0,          0}, /* 82801AA (ICH) */
		{0x2420, 0x58, 0x0FE30000,          0,          0}, /* 82801AB (ICH0) */
		{0x2440, 0x58, 0x1BFF391B,          0,          0}, /* 82801BA (ICH2) */
		{0x244C, 0x58, 0x1A23399B,          0,          0}, /* 82801BAM (ICH2M) */
		{0x2450, 0x58, 0x1BFF0000,          0,          0}, /* 82801E (C-ICH) */
		{0x2480, 0x58, 0x1BFF0000, 0x00000FFF,          0}, /* 82801CA (ICH3-S) */
		{0x248C, 0x58, 0x1A230000, 0x00000FFF,          0}, /* 82801CAM (ICH3-M) */
		{0x24C0, 0x58, 0x1BFF0000, 0x00000FFF,          0}, /* 82801DB/DBL (ICH4/ICH4-L) */
		{0x24CC, 0x58, 0x1A030000, 0x00000FFF,          0}, /* 82801DBM (ICH4-M) */
		{0x24D0, 0x58, 0x1BFF0000, 0x00030305,          0}, /* 82801EB/ER (ICH5/ICH5R) */
		{0x2640, 0x48, 0x1BFF0000, 0x00030307,          0}, /* 82801FB/FR (ICH6/ICH6R) */
		{0x2641, 0x48, 0x1BFF0000, 0x00030307,          0}, /* 82801FBM (ICH6M) */
		{0x27B0, 0x48, 0xFFFFFFFF, 0x000300FF,          0}, /* 82801GDH (ICH7 DH) */
		{0x27B8, 0x48, 0xFFFFFFFF, 0x000300FF,          0}, /* 82801GB/GR (ICH7 Family) */
		{0x27B9, 0x48, 0xFFEBFFFE, 0x000300FE,          0}, /* 82801GBM (ICH7-M) */
		{0x27BD, 0x48, 0xFFEBFFFE, 0x000300FE,          0}, /* 82801GHM (ICH7-M DH) */
		{0x2810, 0x48, 0xFFFFFFFF, 0x00FF0FFF,          0}, /* 82801HB/HR (ICH8/R) */
		{0x2811, 0x48, 0xFFFFFFFF, 0x00FF0FFF,          0}, /* 82801HBM (ICH8M-E) */
		{0x2812, 0x48, 0xFFFFFFFF, 0x00FF0FFF,          0}, /* 82801HH (ICH8DH) */
		{0x2814, 0x48, 0xFFFFFFFF, 0x00FF0FFF,          0}, /* 82801HO (ICH8DO) */
		{0x2815, 0x48, 0xFFFFFFFF, 0x00FF0FFF,          0}, /* 82801HEM (ICH8M) */
		{0x2912, 0x48, 0xFFFFFFFF, 0x00FFFFFF,          0}, /* 82801IH (ICH9DH) */
		{0x2914, 0x48, 0xFFFFFFFF, 0x00FFFFFF,          0}, /* 82801IO (ICH9DO) */
		{0x2916, 0x48, 0xFFFFFFFF, 0x00FFFFFF,          0}, /* 82801IR (ICH9R) */
		{0x2917, 0x48, 0xFFFFFFFF, 0x00FFFFFF,          0}, /* 82801IEM (ICH9M-E) */
		{0x2918, 0x48, 0xFFFFFFFF, 0x00FFFFFF,          0}, /* 82801IB (ICH9) */
		{0x2919, 0x48, 0xFFFFFFFF, 0x00FFFFFF,          0}, /* 82801IBM (ICH9M) */
		{0x3A14, 0x48, 0xFFFFFFFF, 0xFFFFFFFF, 0x00000100}, /* 82801JDO (ICH10DO) */
		{0x3A16, 0x48, 0xFFFFFFFF, 0xFFFFFFFF, 0x00000100}, /* 82801JIR (ICH10R) */
		{0x3A18, 0x48, 0xFFFFFFFF, 0xFFFFFFFF, 0x00000100}, /* 82801JIB (ICH10) */
		{0x3A1A, 0x48, 0xFFFFFFFF, 0xFFFFFFFF, 0x00000100}, /* 82801JD (ICH10D) */
		{0, 0, 0, 0, 0} /* end marker */
	};

	struct pci_dev *dev;
	uint16_t base;
	uint32_t tmp;
	int i, allowed;

	/* First, look for a known LPC bridge */
	for (dev = pacc->devices; dev; dev = dev->next) {
		pci_fill_info(dev, PCI_FILL_IDENT);
		uint16_t device_class;
		/* libpci before version 2.2.4 does not store class info. */
		device_class = pci_read_word(dev, PCI_CLASS_DEVICE);
		if ((dev->vendor_id == 0x8086) &&
		    (device_class == 0x0601)) { /* ISA bridge */
			/* Is this device in our list? */
			for (i = 0; intel_ich_gpio_table[i].id; i++)
				if (dev->device_id == intel_ich_gpio_table[i].id)
					break;

			if (intel_ich_gpio_table[i].id)
				break;
		}
	}

	if (!dev) {
		msg_perr("\nERROR: No known Intel LPC bridge found.\n");
		return -1;
	}

	/*
	 * According to the datasheets, all Intel ICHs have the GPIO bar 5:1
	 * strapped to zero. From some mobile ICH9 version on, this becomes
	 * 6:1. The mask below catches all.
	 */
	base = pci_read_word(dev, intel_ich_gpio_table[i].base_reg) & 0xFFC0;

	/* Check whether the line is allowed. */
	if (gpio < 32)
		allowed = (intel_ich_gpio_table[i].bank0 >> gpio) & 0x01;
	else if (gpio < 64)
		allowed = (intel_ich_gpio_table[i].bank1 >> (gpio - 32)) & 0x01;
	else
		allowed = (intel_ich_gpio_table[i].bank2 >> (gpio - 64)) & 0x01;

	if (!allowed) {
		msg_perr("\nERROR: This Intel LPC bridge does not allow"
			 " setting GPIO%02d\n", gpio);
		return -1;
	}

	msg_pdbg("\nIntel ICH LPC bridge: %sing GPIO%02d.\n",
		 raise ? "Rais" : "Dropp", gpio);

	if (gpio < 32) {
		/* Set line to GPIO. */
		tmp = INL(base);
		/* ICH/ICH0 multiplexes 27/28 on the line set. */
		if ((gpio == 28) &&
		    ((dev->device_id == 0x2410) || (dev->device_id == 0x2420)))
			tmp |= 1 << 27;
		else
			tmp |= 1 << gpio;
		OUTL(tmp, base);

		/* As soon as we are talking to ICH8 and above, this register
		   decides whether we can set the gpio or not. */
		if (dev->device_id > 0x2800) {
			tmp = INL(base);
			if (!(tmp & (1 << gpio))) {
				msg_perr("\nERROR: This Intel LPC bridge"
					" does not allow setting GPIO%02d\n",
					gpio);
				return -1;
			}
		}

		/* Set GPIO to OUTPUT. */
		tmp = INL(base + 0x04);
		tmp &= ~(1 << gpio);
		OUTL(tmp, base + 0x04);

		/* Raise GPIO line. */
		tmp = INL(base + 0x0C);
		if (raise)
			tmp |= 1 << gpio;
		else
			tmp &= ~(1 << gpio);
		OUTL(tmp, base + 0x0C);
	} else if (gpio < 64) {
		gpio -= 32;

		/* Set line to GPIO. */
		tmp = INL(base + 0x30);
		tmp |= 1 << gpio;
		OUTL(tmp, base + 0x30);

		/* As soon as we are talking to ICH8 and above, this register
		   decides whether we can set the gpio or not. */
		if (dev->device_id > 0x2800) {
			tmp = INL(base + 30);
			if (!(tmp & (1 << gpio))) {
				msg_perr("\nERROR: This Intel LPC bridge"
					" does not allow setting GPIO%02d\n",
					gpio + 32);
				return -1;
			}
		}

		/* Set GPIO to OUTPUT. */
		tmp = INL(base + 0x34);
		tmp &= ~(1 << gpio);
		OUTL(tmp, base + 0x34);

		/* Raise GPIO line. */
		tmp = INL(base + 0x38);
		if (raise)
			tmp |= 1 << gpio;
		else
			tmp &= ~(1 << gpio);
		OUTL(tmp, base + 0x38);
	} else {
		gpio -= 64;

		/* Set line to GPIO. */
		tmp = INL(base + 0x40);
		tmp |= 1 << gpio;
		OUTL(tmp, base + 0x40);

		tmp = INL(base + 40);
		if (!(tmp & (1 << gpio))) {
			msg_perr("\nERROR: This Intel LPC bridge does "
				"not allow setting GPIO%02d\n", gpio + 64);
			return -1;
		}

		/* Set GPIO to OUTPUT. */
		tmp = INL(base + 0x44);
		tmp &= ~(1 << gpio);
		OUTL(tmp, base + 0x44);

		/* Raise GPIO line. */
		tmp = INL(base + 0x48);
		if (raise)
			tmp |= 1 << gpio;
		else
			tmp &= ~(1 << gpio);
		OUTL(tmp, base + 0x48);
	}

	return 0;
}

/*
 * Suited for:
 *  - abit IP35: Intel P35 + ICH9R
 *  - abit IP35 Pro: Intel P35 + ICH9R
 *  - ASUS P5LD2
 *  - ASUS P5LD2-MQ
 *  - ASUS P5LD2-VM
 *  - ASUS P5LD2-VM DH
 *  - ASUS P5W DH Deluxe
 */
static int intel_ich_gpio16_raise(void)
{
	return intel_ich_gpio_set(16, 1);
}

/*
 * Suited for:
 *  - HP Puffer2-UL8E (ASUS PTGD-LA OEM): LGA775 + 915 + ICH6
 */
static int intel_ich_gpio18_raise(void)
{
	return intel_ich_gpio_set(18, 1);
}

/*
 * Suited for:
 *  - MSI MS-7046: LGA775 + 915P + ICH6
 */
static int intel_ich_gpio19_raise(void)
{
	return intel_ich_gpio_set(19, 1);
}

/*
 * Suited for:
 *  - ASUS P5BV-R: LGA775 + 3200 + ICH7
 *  - AOpen i965GMt-LA: Intel Socket479 + 965GM + ICH8M
 */
static int intel_ich_gpio20_raise(void)
{
	return intel_ich_gpio_set(20, 1);
}

/*
 * Suited for:
 *  - ASUS CUSL2-C: Intel socket370 + 815 + ICH2
 *  - ASUS P4B266LM (Sony Vaio PCV-RX650): socket478 + 845D + ICH2
 *  - ASUS P4C800-E Deluxe: socket478 + 875P + ICH5
 *  - ASUS P4P800: Intel socket478 + 865PE + ICH5R
 *  - ASUS P4P800-E Deluxe: Intel socket478 + 865PE + ICH5R
 *  - ASUS P4P800-VM: Intel socket478 + 865PE + ICH5R
 *  - ASUS P4P800-X: Intel socket478 + 865PE + ICH5R
 *  - ASUS P4P800SE: Intel socket478 + 865PE + ICH5R
 *  - ASUS P5GD1 Pro: Intel LGA 775 + 915P + ICH6R
 *  - ASUS P5GD2 Premium: Intel LGA775 + 915G + ICH6R
 *  - ASUS P5GDC Deluxe: Intel socket775 + 915P + ICH6R
 *  - ASUS P5PE-VM: Intel LGA775 + 865G + ICH5
 *  - ASUS TUSL2-C: Intel socket370 + 815 + ICH2
 *  - Samsung Polaris 32: socket478 + 865P + ICH5
 */
static int intel_ich_gpio21_raise(void)
{
	return intel_ich_gpio_set(21, 1);
}

/*
 * Suited for:
 *  - ASUS P4B266: socket478 + Intel 845D + ICH2
 *  - ASUS P4B533-E: socket478 + 845E + ICH4
 *  - ASUS P4B-MX variant in HP Vectra VL420 SFF: socket478 + 845D + ICH2
 *  - TriGem Anaheim-3: socket370 + Intel 810 + ICH
 */
static int intel_ich_gpio22_raise(void)
{
	return intel_ich_gpio_set(22, 1);
}

/*
 * Suited for:
 *  - ASUS A8Jm (laptop): Intel 945 + ICH7
 *  - ASUS P5LP-LE used in ...
 *    - HP Media Center m7270.fr Desktop PC as "Lithium-UL8E"
 *    - Epson Endeavor MT7700
 */
static int intel_ich_gpio34_raise(void)
{
	return intel_ich_gpio_set(34, 1);
}

/*
 * Suited for:
 *  - AOpen i945GMx-VFX: Intel 945GM + ICH7-M used in ...
 *    - FSC ESPRIMO Q5010 (SMBIOS: D2544-B1)
 */
static int intel_ich_gpio38_raise(void)
{
	return intel_ich_gpio_set(38, 1);
}

/*
 * Suited for:
 *  - ASUS M6Ne (laptop): socket 479M (guessed) + Intel 855PM + ICH4-M
 */
static int intel_ich_gpio43_raise(void)
{
	return intel_ich_gpio_set(43, 1);
}

/*
 * Suited for:
 *  - HP Vectra VL400: 815 + ICH + PC87360
 */
static int board_hp_vl400(void)
{
	int ret;
	ret = intel_ich_gpio_set(25, 1);	/* Master write enable ? */
	if (!ret)
		ret = pc8736x_gpio_set(PC87360_ID, 0x09, 1);	/* #WP ? */
	if (!ret)
		ret = pc8736x_gpio_set(PC87360_ID, 0x27, 1);	/* #TBL */
	return ret;
}

/*
 * Suited for:
 *  - HP e-Vectra P2706T: 810E + ICH + PC87364
 */
static int board_hp_p2706t(void)
{
	int ret;
	ret = pc8736x_gpio_set(PC87364_ID, 0x25, 1);
	if (!ret)
		ret = pc8736x_gpio_set(PC87364_ID, 0x26, 1);
	return ret;
}

/*
 * Suited for:
 *  - Dell PowerEdge 1850: Intel PPGA604 + E7520 + ICH5R
 *  - ASRock P4i65GV: Intel Socket478 + 865GV + ICH5R
 *  - ASRock 775i65G: Intel LGA 775 + 865G + ICH5
 *  - MSI MS-6391 (845 Pro4): Intel Socket478 + 845 + ICH2
 */
static int intel_ich_gpio23_raise(void)
{
	return intel_ich_gpio_set(23, 1);
}

/*
 * Suited for:
 *  - GIGABYTE GA-6IEM: Intel Socket370 + i815 + ICH2
 *  - GIGABYTE GA-8IRML: Intel Socket478 + i845 + ICH2
 */
static int intel_ich_gpio25_raise(void)
{
	return intel_ich_gpio_set(25, 1);
}

/*
 * Suited for:
 *  - IBASE MB899: i945GM + ICH7
 */
static int intel_ich_gpio26_raise(void)
{
	return intel_ich_gpio_set(26, 1);
}

/*
 * Suited for:
 *  - ASUS DSAN-DX
 *  - P4SD-LA (HP OEM): i865 + ICH5
 *  - GIGABYTE GA-8IP775: 865P + ICH5
 *  - GIGABYTE GA-8PE667 Ultra 2: socket 478 + i845PE + ICH4
 *  - MSI MS-6788-40 (aka 848P Neo-V)
 */
static int intel_ich_gpio32_raise(void)
{
	return intel_ich_gpio_set(32, 1);
}

/*
 * Suited for:
 *  - AOpen i975Xa-YDG: i975X + ICH7 + W83627EHF
 */
static int board_aopen_i975xa_ydg(void)
{
	int ret;

	/* Vendor BIOS ends up in LDN6... maybe the board enable is wrong,
	 * or perhaps it's not needed at all?
	 * The regs it tries to touch are 0xF0, 0xF1, 0xF2 which means if it
	 * were in the right LDN, it would have to be GPIO1 or GPIO3.
	 */
/*
	ret = winbond_gpio_set(0x2e, WINBOND_W83627EHF_ID, x, 0)
	if (!ret)
*/
		ret = intel_ich_gpio_set(33, 1);

	return ret;
}

/*
 * Suited for:
 *  - Acorp 6A815EPD: socket 370 + intel 815 + ICH2
 */
static int board_acorp_6a815epd(void)
{
	int ret;

	/* Lower Blocks Lock -- pin 7 of PLCC32 */
	ret = intel_ich_gpio_set(22, 1);
	if (!ret) /* Top Block Lock -- pin 8 of PLCC32 */
		ret = intel_ich_gpio_set(23, 1);

	return ret;
}

/*
 * Suited for:
 *  - Kontron 986LCD-M: Socket478 + 915GM + ICH7R
 */
static int board_kontron_986lcd_m(void)
{
	int ret;

	ret = intel_ich_gpio_set(34, 1); /* #TBL */
	if (!ret)
		ret = intel_ich_gpio_set(35, 1); /* #WP */

	return ret;
}

/*
 * Suited for:
 *  - Soyo SY-7VCA: Pro133A + VT82C686
 */
static int via_apollo_gpo_set(int gpio, int raise)
{
	struct pci_dev *dev;
	uint32_t base, tmp;

	/* VT82C686 power management */
	dev = pci_dev_find(0x1106, 0x3057);
	if (!dev) {
		msg_perr("\nERROR: VT82C686 PM device not found.\n");
		return -1;
	}

	msg_pdbg("\nVIA Apollo ACPI: %sing GPIO%02d.\n",
		 raise ? "Rais" : "Dropp", gpio);

	/* Select GPO function on multiplexed pins. */
	tmp = pci_read_byte(dev, 0x54);
	switch (gpio) {
	case 0:
		tmp &= ~0x03;
		break;
	case 1:
		tmp |= 0x04;
		break;
	case 2:
		tmp |= 0x08;
		break;
	case 3:
		tmp |= 0x10;
		break;
	}
	pci_write_byte(dev, 0x54, tmp);

	/* PM IO base */
	base = pci_read_long(dev, 0x48) & 0x0000FF00;

	/* Drop GPO0 */
	tmp = INL(base + 0x4C);
	if (raise)
		tmp |= 1U << gpio;
	else
		tmp &= ~(1U << gpio);
	OUTL(tmp, base + 0x4C);

	return 0;
}

/*
 * Suited for:
 *  - abit VT6X4: Pro133x + VT82C686A
 *  - abit VA6: Pro133x + VT82C686A
 */
static int via_apollo_gpo4_lower(void)
{
	return via_apollo_gpo_set(4, 0);
}

/*
 * Suited for:
 *  - Soyo SY-7VCA: Pro133A + VT82C686
 */
static int via_apollo_gpo0_lower(void)
{
	return via_apollo_gpo_set(0, 0);
}

/*
 * Enable some GPIO pin on SiS southbridge and enables SIO flash writes.
 *
 * Suited for:
 *  - MSI 651M-L: SiS651 / SiS962
 *  - GIGABYTE GA-8SIMLFS 2.0
 *  - GIGABYTE GA-8SIMLH
 */
static int sis_gpio0_raise_and_w836xx_memw(void)
{
	struct pci_dev *dev;
	uint16_t base, temp;

	dev = pci_dev_find(0x1039, 0x0962);
	if (!dev) {
		msg_perr("Expected south bridge not found\n");
		return 1;
	}

	base = pci_read_word(dev, 0x74);
	temp = INW(base + 0x68);
	temp &= ~(1 << 0);		/* Make pin output? */
	OUTW(temp, base + 0x68);

	temp = INW(base + 0x64);
	temp |= (1 << 0);		/* Raise output? */
	OUTW(temp, base + 0x64);

	w836xx_memw_enable(0x2E);

	return 0;
}

/*
 * Find the runtime registers of an SMSC Super I/O, after verifying its
 * chip ID.
 *
 * Returns the base port of the runtime register block, or 0 on error.
 */
static uint16_t smsc_find_runtime(uint16_t sio_port, uint16_t chip_id,
                                  uint8_t logical_device)
{
	uint16_t rt_port = 0;

	/* Verify the chip ID. */
	OUTB(0x55, sio_port);  /* Enable configuration. */
	if (sio_read(sio_port, 0x20) != chip_id) {
		msg_perr("\nERROR: SMSC Super I/O not found.\n");
		goto out;
	}

	/* If the runtime block is active, get its address. */
	sio_write(sio_port, 0x07, logical_device);
	if (sio_read(sio_port, 0x30) & 1) {
		rt_port = (sio_read(sio_port, 0x60) << 8)
		          | sio_read(sio_port, 0x61);
	}

	if (rt_port == 0) {
		msg_perr("\nERROR: "
			"Super I/O runtime interface not available.\n");
	}
out:
	OUTB(0xaa, sio_port);  /* Disable configuration. */
	return rt_port;
}

/*
 * Disable write protection on the Mitac 6513WU. WP# on the FWH is
 * connected to GP30 on the Super I/O, and TBL# is always high.
 */
static int board_mitac_6513wu(void)
{
	struct pci_dev *dev;
	uint16_t rt_port;
	uint8_t val;

	dev = pci_dev_find(0x8086, 0x2410);	/* Intel 82801AA ISA bridge */
	if (!dev) {
		msg_perr("\nERROR: Intel 82801AA ISA bridge not found.\n");
		return -1;
	}

	rt_port = smsc_find_runtime(0x4e, 0x54 /* LPC47U33x */, 0xa);
	if (rt_port == 0)
		return -1;

	/* Configure the GPIO pin. */
	val = INB(rt_port + 0x33);  /* GP30 config */
	val &= ~0x87;               /* Output, non-inverted, GPIO, push/pull */
	OUTB(val, rt_port + 0x33);

	/* Disable write protection. */
	val = INB(rt_port + 0x4d);  /* GP3 values */
	val |= 0x01;                /* Set GP30 high. */
	OUTB(val, rt_port + 0x4d);

	return 0;
}

/*
 * Suited for:
 *  - abit AV8: Socket939 + K8T800Pro + VT8237
 */
static int board_abit_av8(void)
{
	uint8_t val;

	/* Raise GPO pins GP22 & GP23 */
	val = INB(0x404E);
	val |= 0xC0;
	OUTB(val, 0x404E);

	return 0;
}

/*
 * Suited for:
 *  - ASUS A7V333: VIA KT333 + VT8233A + IT8703F
 *  - ASUS A7V8X: VIA KT400 + VT8235 + IT8703F
 */
static int it8703f_gpio51_raise(void)
{
	uint16_t id, base;
	uint8_t tmp;

	/* Find the IT8703F. */
	w836xx_ext_enter(0x2E);
	id = (sio_read(0x2E, 0x20) << 8) | sio_read(0x2E, 0x21);
	w836xx_ext_leave(0x2E);

	if (id != 0x8701) {
		msg_perr("\nERROR: IT8703F Super I/O not found.\n");
		return -1;
	}

	/* Get the GP567 I/O base. */
	w836xx_ext_enter(0x2E);
	sio_write(0x2E, 0x07, 0x0C);
	base = (sio_read(0x2E, 0x60) << 8) | sio_read(0x2E, 0x61);
	w836xx_ext_leave(0x2E);

	if (!base) {
		msg_perr("\nERROR: Failed to read IT8703F Super I/O GPIO"
			" Base.\n");
		return -1;
	}

	/* Raise GP51. */
	tmp = INB(base);
	tmp |= 0x02;
	OUTB(tmp, base);

	return 0;
}

/*
 * General routine for raising/dropping GPIO lines on the ITE IT87xx.
 */
static int it87_gpio_set(unsigned int gpio, int raise)
{
	int allowed, sio;
	unsigned int port;
	uint16_t base, sioport;
	uint8_t tmp;

	/* IT87 GPIO configuration table */
	static const struct it87cfg {
		uint16_t id;
		uint8_t base_reg;
		uint32_t bank0;
		uint32_t bank1;
		uint32_t bank2;
	} it87_gpio_table[] = {
		{0x8712, 0x62, 0xCFF3FC00, 0x00FCFF3F,          0},
		{0x8718, 0x62, 0xCFF37C00, 0xF3FCDF3F, 0x0000000F},
		{0, 0, 0, 0, 0} /* end marker */
	};
	const struct it87cfg *cfg = NULL;

	/* Find the Super I/O in the probed list */
	for (sio = 0; sio < superio_count; sio++) {
		int i;
		if (superios[sio].vendor != SUPERIO_VENDOR_ITE)
			continue;

		/* Is this device in our list? */
		for (i = 0; it87_gpio_table[i].id; i++)
			if (superios[sio].model == it87_gpio_table[i].id) {
				cfg = &it87_gpio_table[i];
				goto found;
			}
	}

	if (cfg == NULL) {
		msg_perr("\nERROR: No IT87 Super I/O GPIO configuration "
			 "found.\n");
		return -1;
	}

found:
	/* Check whether the gpio is allowed. */
	if (gpio < 32)
		allowed = (cfg->bank0 >> gpio) & 0x01;
	else if (gpio < 64)
		allowed = (cfg->bank1 >> (gpio - 32)) & 0x01;
	else if (gpio < 96)
		allowed = (cfg->bank2 >> (gpio - 64)) & 0x01;
	else
		allowed = 0;

	if (!allowed) {
		msg_perr("\nERROR: IT%02X does not allow setting GPIO%02u.\n",
			 cfg->id, gpio);
		return -1;
	}

	/* Read the Simple I/O Base Address Register */
	sioport = superios[sio].port;
	enter_conf_mode_ite(sioport);
	sio_write(sioport, 0x07, 0x07);
	base = (sio_read(sioport, cfg->base_reg) << 8) |
		sio_read(sioport, cfg->base_reg + 1);
	exit_conf_mode_ite(sioport);

	if (!base) {
		msg_perr("\nERROR: Failed to read IT87 Super I/O GPIO Base.\n");
		return -1;
	}

	msg_pdbg("Using IT87 GPIO base 0x%04x\n", base);

	port = gpio / 10 - 1;
	gpio %= 10;

	/* set GPIO. */
	tmp = INB(base + port);
	if (raise)
		tmp |= 1 << gpio;
	else
		tmp &= ~(1 << gpio);
	OUTB(tmp, base + port);

	return 0;
}

/*
 * Suited for:
 * - ASUS A7N8X-VM/400: NVIDIA nForce2 IGP2 + IT8712F
 */
static int it8712f_gpio12_raise(void)
{
	return it87_gpio_set(12, 1);
}

/*
 * Suited for:
 * - ASUS A7V600-X: VIA KT600 + VT8237 + IT8712F
 * - ASUS A7V8X-X: VIA KT400 + VT8235 + IT8712F
 */
static int it8712f_gpio31_raise(void)
{
	return it87_gpio_set(32, 1);
}

/*
 * Suited for:
 * - ASUS P5N-D: NVIDIA MCP51 + IT8718F
 * - ASUS P5N-E SLI: NVIDIA MCP51 + IT8718F
 */
static int it8718f_gpio63_raise(void)
{
	return it87_gpio_set(63, 1);
}

/*
 * Suited for all boards with ambiguous DMI chassis information, which should be
 * whitelisted because they are known to work:
 * - ASRock IMB-A180(-H)
 * - Intel D945GCNL
 * - MSC Q7 Tunnel Creek Module (Q7-TCTC)
 */
static int p2_not_a_laptop(void)
{
	/* label this board as not a laptop */
	is_laptop = 0;
	msg_pdbg("Laptop detection overridden by P2 board enable.\n");
	return 0;
}

/*
 * Suited for all laptops, which are known to *not* have interfering embedded controllers.
 */
static int p2_whitelist_laptop(void)
{
	is_laptop = 1;
	laptop_ok = true;
	msg_pdbg("Whitelisted laptop detected.\n");
	return 0;
}

#endif

/*
 * Below is the list of boards which need a special "board enable" code in
 * flashrom before their ROM chip can be accessed/written to.
 *
 * NOTE: Please add boards that _don't_ need such enables or don't work yet
 *       to the respective tables in print.c. Thanks!
 *
 * We use 2 sets of PCI IDs here, you're free to choose which is which. This
 * is to provide a very high degree of certainty when matching a board on
 * the basis of subsystem/card IDs. As not every vendor handles
 * subsystem/card IDs in a sane manner.
 *
 * Keep the second set NULLed if it should be ignored. Keep the subsystem IDs
 * and the dmi identifier NULLed if they don't identify the board fully to disable autodetection.
 * But please take care to provide an as complete set of pci ids as possible;
 * autodetection is the preferred behaviour and we would like to make sure that
 * matches are unique.
 *
 * If PCI IDs are not sufficient for board matching, the match can be further
 * constrained by a string that has to be present in the DMI database for
 * the baseboard or the system entry. The pattern is matched by case sensitive
 * substring match, unless it is anchored to the beginning (with a ^ in front)
 * or the end (with a $ at the end). Both anchors may be specified at the
 * same time to match the full field.
 *
 * When a board is matched through DMI, the first and second main PCI IDs
 * and the first subsystem PCI ID have to match as well. If you specify the
 * first subsystem ID as 0x0:0x0, the DMI matching code expects that the
 * subsystem ID of that device is indeed zero.
 *
 * The coreboot ids are used two fold. When running with a coreboot firmware,
 * the ids uniquely matches the coreboot board identification string. When a
 * legacy bios is installed and when autodetection is not possible, these ids
 * can be used to identify the board through the -p internal:mainboard=
 * programmer parameter.
 *
 * When a board is identified through its coreboot ids (in both cases), the
 * main pci ids are still required to match, as a safeguard.
 */

/* Please keep this list alphabetically ordered by vendor/board name. */
const struct board_match board_matches[] = {

	/* first pci-id set [4],          second pci-id set [4],          dmi identifier, coreboot id [2],  phase, vendor name,  board name       max_rom_...  OK? flash enable */
#if defined(__i386__) || defined(__x86_64__)
	{0x10DE, 0x0547, 0x147B, 0x1C2F,  0x10DE, 0x0548, 0x147B, 0x1C2F, NULL,         NULL, NULL,           P3, "abit",        "AN-M2",                 0,   NT, nvidia_mcp_gpio2_raise},
	{0x1106, 0x0282, 0x147B, 0x1415,  0x1106, 0x3227, 0x147B, 0x1415, "^AV8 ",      NULL, NULL,           P3, "abit",        "AV8",                   0,   OK, board_abit_av8},
	{0x8086, 0x7190,      0,      0,  0x8086, 0x7110,      0,      0, NULL /* "^I440BX-W977$" */, "abit", "bf6", P3, "abit", "BF6",                   0,   OK, intel_piix4_gpo26_lower},
	{0x8086, 0x7190,      0,      0,  0x8086, 0x7110,      0,      0, "^i440BX-W977 (BM6)$", NULL, NULL,  P3, "abit",        "BM6",                   0,   OK, intel_piix4_gpo26_lower},
	{0x8086, 0x24d3, 0x147b, 0x1014,  0x8086, 0x2578, 0x147b, 0x1014, NULL,         NULL, NULL,           P3, "abit",        "IC7",                   0,   NT, intel_ich_gpio23_raise},
	{0x8086, 0x2930, 0x147b, 0x1084,  0x11ab, 0x4364, 0x147b, 0x1084, NULL,         NULL, NULL,           P3, "abit",        "IP35",                  0,   OK, intel_ich_gpio16_raise},
	{0x8086, 0x2930, 0x147b, 0x1083,  0x10ec, 0x8167, 0x147b, 0x1083, NULL,         NULL, NULL,           P3, "abit",        "IP35 Pro",              0,   OK, intel_ich_gpio16_raise},
	{0x10de, 0x0050, 0x147b, 0x1c1a,  0x10de, 0x0052, 0x147b, 0x1c1a, NULL,         NULL, NULL,           P3, "abit",        "KN8 Ultra",             0,   NT, nvidia_mcp_gpio2_lower},
	{0x10de, 0x0369, 0x147b, 0x1c20,  0x10de, 0x0360, 0x147b, 0x1c20, "^KN9(NF-MCP55 series)$", NULL, NULL, P3, "abit",      "KN9 Ultra",             0,   OK, nvidia_mcp_gpio2_lower},
	{0x10de, 0x01e0, 0x147b, 0x1c00,  0x10de, 0x0060, 0x147B, 0x1c00, NULL,         NULL, NULL,           P3, "abit",        "NF7-S",                 0,   OK, nvidia_mcp_gpio8_raise},
	{0x10de, 0x02f0, 0x147b, 0x1c26,  0x10de, 0x0260, 0x147b, 0x1c26, NULL,         NULL, NULL,           P3, "abit",        "NF-M2 nView",           0,   OK, nvidia_mcp_gpio4_lower},
	{0x1106, 0x0691,      0,      0,  0x1106, 0x3057,      0,      0, "(VA6)$",     NULL, NULL,           P3, "abit",        "VA6",                   0,   OK, via_apollo_gpo4_lower},
	{0x1106, 0x0691,      0,      0,  0x1106, 0x3057,      0,      0, NULL,         "abit", "vt6x4",      P3, "abit",        "VT6X4",                 0,   OK, via_apollo_gpo4_lower},
	{0x105a, 0x0d30, 0x105a, 0x4d33,  0x8086, 0x1130, 0x8086,      0, NULL,         NULL, NULL,           P3, "Acorp",       "6A815EPD",              0,   OK, board_acorp_6a815epd},
	{0x1022, 0x746B,      0,      0,  0x1022, 0x7460,      0,      0, NULL,         "AGAMI", "ARUMA",     P3, "agami",       "Aruma",                 0,   OK, w83627hf_gpio24_raise_2e},
	{0x1106, 0x3177, 0x17F2, 0x3177,  0x1106, 0x3148, 0x17F2, 0x3148, NULL,         NULL, NULL,           P3, "Albatron",    "PM266A Pro",            0,   OK, w836xx_memw_enable_2e},
	{0x1022, 0x2090,      0,      0,  0x1022, 0x2080,      0,      0, NULL,        "artecgroup", "dbe61", P3, "Artec Group", "DBE61",                 0,   OK, board_artecgroup_dbe6x},
	{0x1022, 0x2090,      0,      0,  0x1022, 0x2080,      0,      0, NULL,        "artecgroup", "dbe62", P3, "Artec Group", "DBE62",                 0,   OK, board_artecgroup_dbe6x},
	{0x8086, 0x27b9, 0xa0a0, 0x0632,  0x8086, 0x27da, 0xa0a0, 0x0632, NULL,         NULL, NULL,           P3, "AOpen",       "i945GMx-VFX",           0,   OK, intel_ich_gpio38_raise},
	{0x8086, 0x2a00, 0xa0a0, 0x063e,  0x8086, 0x2815, 0xa0a0, 0x063e, NULL,         NULL, NULL,           P3, "AOpen",       "i965GMt-LA",            0,   OK, intel_ich_gpio20_raise},
	{0x8086, 0x277c, 0xa0a0, 0x060b,  0x8086, 0x27da, 0xa0a0, 0x060b, NULL,         NULL, NULL,           P3, "AOpen",       "i975Xa-YDG",            0,   OK, board_aopen_i975xa_ydg},
	{0x8086, 0x27A0, 0x8086, 0x7270,  0x8086, 0x27B9, 0x8086, 0x7270, "^iMac5,2$",  NULL, NULL,           P2, "Apple",       "iMac5,2",               0,   OK, p2_whitelist_laptop},
	{0x8086, 0x27A0, 0x8086, 0x7270,  0x8086, 0x27B9, 0x8086, 0x7270, "^MacBook2,1$", NULL, NULL,         P2, "Apple",       "MacBook2,1",            0,   OK, p2_whitelist_laptop},
	{0x8086, 0x27b8, 0x1849, 0x27b8,  0x8086, 0x27da, 0x1849, 0x27da, "^ConRoeXFire-eSATA2", NULL, NULL,  P3, "ASRock",      "ConRoeXFire-eSATA2",    0,   OK, intel_ich_gpio16_raise},
	{0x1022, 0x1536, 0x1849, 0x1536,  0x1022, 0x780e, 0x1849, 0x780e, "^Kabini CRB$", NULL, NULL,         P2, "ASRock",      "IMB-A180(-H)",          0,   OK, p2_not_a_laptop},
	{0x1039, 0x0741, 0x1849, 0x0741,  0x1039, 0x5513, 0x1849, 0x5513, "^K7S41 $",   NULL, NULL,           P3, "ASRock",      "K7S41",                 0,   OK, w836xx_memw_enable_2e},
	{0x1039, 0x0741, 0x1849, 0x0741,  0x1039, 0x5513, 0x1849, 0x5513, "^K7S41GX$",  NULL, NULL,           P3, "ASRock",      "K7S41GX",               0,   OK, w836xx_memw_enable_2e},
	{0x8086, 0x24D4, 0x1849, 0x24D0,  0x8086, 0x24D5, 0x1849, 0x9739, NULL,         NULL, NULL,           P3, "ASRock",      "P4i65GV",               0,   OK, intel_ich_gpio23_raise},
	{0x8086, 0x2570, 0x1849, 0x2570,  0x8086, 0x24d3, 0x1849, 0x24d0, NULL,         NULL, NULL,           P3, "ASRock",      "775i65G",               0,   OK, intel_ich_gpio23_raise},
	{0x10DE, 0x0060, 0x1043, 0x80AD,  0x10DE, 0x01E0, 0x1043, 0x80C0, NULL,         NULL, NULL,           P3, "ASUS",        "A7N8X-VM/400",          0,   OK, it8712f_gpio12_raise},
	{0x1106, 0x3189, 0x1043, 0x807F,  0x1106, 0x3065, 0x1043, 0x80ED, NULL,         NULL, NULL,           P3, "ASUS",        "A7V600-X",              0,   OK, it8712f_gpio31_raise},
	{0x1106, 0x3177, 0x1043, 0x80F9,  0x1106, 0x3205, 0x1043, 0x80F9, NULL,         NULL, NULL,           P3, "ASUS",        "A7V8X-MX",              0,   OK, w836xx_memw_enable_2e},
	{0x1106, 0x3177, 0x1043, 0x80A1,  0x1106, 0x3205, 0x1043, 0x8118, NULL,         NULL, NULL,           P3, "ASUS",        "A7V8X-MX SE",           0,   OK, w836xx_memw_enable_2e},
	{0x1106, 0x3189, 0x1043, 0x807F,  0x1106, 0x3177, 0x1043, 0x808C, NULL,         NULL, NULL,           P3, "ASUS",        "A7V8X",                 0,   OK, it8703f_gpio51_raise},
	{0x1106, 0x3099, 0x1043, 0x807F,  0x1106, 0x3147, 0x1043, 0x808C, NULL,         NULL, NULL,           P3, "ASUS",        "A7V333",                0,   OK, it8703f_gpio51_raise},
	{0x1106, 0x3189, 0x1043, 0x807F,  0x1106, 0x3177, 0x1043, 0x80A1, NULL,         NULL, NULL,           P3, "ASUS",        "A7V8X-X",               0,   OK, it8712f_gpio31_raise},
	{0x1002, 0x4372, 0x103c, 0x2a26,  0x1002, 0x4377, 0x103c, 0x2a26, NULL,         NULL, NULL,           P3, "ASUS",        "A8AE-LE",               0,   OK, amd_sbxxx_gpio9_raise},
	{0x8086, 0x27A0, 0x1043, 0x1287,  0x8086, 0x27DF, 0x1043, 0x1287, "^A8J",       NULL, NULL,           P3, "ASUS",        "A8Jm",                  0,   NT, intel_ich_gpio34_raise},
	{0x10DE, 0x0260, 0x103C, 0x2A34,  0x10DE, 0x0264, 0x103C, 0x2A34, "NODUSM3",    NULL, NULL,           P3, "ASUS",        "A8M2N-LA (NodusM3-GL8E)",  0,   OK, nvidia_mcp_gpio0_raise},
	{0x10DE, 0x0260, 0x103c, 0x2a3e,  0x10DE, 0x0264, 0x103c, 0x2a3e, "NAGAMI2L",   NULL, NULL,           P3, "ASUS",        "A8N-LA (Nagami-GL8E)",  0,   OK, nvidia_mcp_gpio0_raise},
	{0x10de, 0x0264, 0x1043, 0x81bc,  0x10de, 0x02f0, 0x1043, 0x81cd, NULL,         NULL, NULL,           P3, "ASUS",        "A8N-VM CSM",            0,   OK, w83627ehf_gpio22_raise_2e},
	{0x8086, 0x65c0, 0x1043, 0x8301,  0x8086, 0x2916, 0x1043, 0x82a6, "^DSAN-DX$",  NULL, NULL,           P3, "ASUS",        "DSAN-DX",               0,   NT, intel_ich_gpio32_raise},
	{0x10DE, 0x0264, 0x1043, 0x81C0,  0x10DE, 0x0260, 0x1043, 0x81C0, NULL,         NULL, NULL,           P3, "ASUS",        "M2NBP-VM CSM",          0,   OK, nvidia_mcp_gpio0_raise},
	{0x1106, 0x1336, 0x1043, 0x80ed,  0x1106, 0x3288, 0x1043, 0x8249, NULL,         NULL, NULL,           P3, "ASUS",        "M2V-MX",                0,   OK, via_vt823x_gpio5_raise},
	{0x8086, 0x24cc,      0,      0,  0x8086, 0x24c3, 0x1043, 0x1869, "^M6Ne$",     NULL, NULL,           P3, "ASUS",        "M6Ne",                  0,   NT, intel_ich_gpio43_raise},
	{0x8086, 0x7180,      0,      0,  0x8086, 0x7110,      0,      0, "^OPLX-M$",   NULL, NULL,           P3, "ASUS",        "OPLX-M",                0,   NT, intel_piix4_gpo18_lower},
	{0x8086, 0x7190,      0,      0,  0x8086, 0x7110,      0,      0, "^P2B-N$",    NULL, NULL,           P3, "ASUS",        "P2B-N",                 0,   OK, intel_piix4_gpo18_lower},
	{0x8086, 0x7190, 0x1043, 0x8024,  0x8086, 0x7110,      0,      0, "P3B-F",      "asus", "p3b-f",      P3, "ASUS",        "P3B-F",                 0,   OK, board_asus_p3b_f},
	{0x8086, 0x1A30, 0x1043, 0x8025,  0x8086, 0x244B, 0x104D, 0x80F0, NULL,         NULL, NULL,           P3, "ASUS",        "P4B266-LM",             0,   OK, intel_ich_gpio21_raise},
	{0x8086, 0x1a30, 0x1043, 0x8070,  0x8086, 0x244b, 0x1043, 0x8028, NULL,         NULL, NULL,           P3, "ASUS",        "P4B266",                0,   OK, intel_ich_gpio22_raise},
	{0x8086, 0x1A30, 0x1043, 0x8088,  0x8086, 0x24C3, 0x1043, 0x8089, NULL,         NULL, NULL,           P3, "ASUS",        "P4B533-E",              0,   NT, intel_ich_gpio22_raise},
	{0x8086, 0x2560, 0x103C, 0x2A00,  0x8086, 0x24C3, 0x103C, 0x2A01, "^Guppy",     NULL, NULL,           P3, "ASUS",        "P4GV-LA (Guppy)",       0,   OK, intel_ich_gpio21_raise},
	{0x8086, 0x24D3, 0x1043, 0x80A6,  0x8086, 0x2578, 0x1043, 0x80F6, NULL,         NULL, NULL,           P3, "ASUS",        "P4C800-E Deluxe",       0,   OK, intel_ich_gpio21_raise},
	{0x8086, 0x2570, 0x1043, 0x80F2,  0x8086, 0x24D5, 0x1043, 0x80F3, NULL,         NULL, NULL,           P3, "ASUS",        "P4P800",                0,   NT, intel_ich_gpio21_raise},
	{0x8086, 0x2570, 0x1043, 0x80f2,  0x8086, 0x24d3, 0x1043, 0x80a6, "^P4P800-E$", NULL, NULL,           P3, "ASUS",        "P4P800-E Deluxe",       0,   OK, intel_ich_gpio21_raise},
	{0x8086, 0x2570, 0x1043, 0x80a5,  0x8086, 0x24d3, 0x1043, 0x80a6, "^P4P800-VM$", NULL, NULL,          P3, "ASUS",        "P4P800-VM",             0,   OK, intel_ich_gpio21_raise},
	{0x8086, 0x2570, 0x1043, 0x80f2,  0x8086, 0x24d3, 0x1043, 0x80a6, "^P4P800-X$", NULL, NULL,           P3, "ASUS",        "P4P800-X",              0,   OK, intel_ich_gpio21_raise},
	{0x8086, 0x2570, 0x1043, 0x80f2,  0x8086, 0x24d3,      0,      0, "^P4P800SE$", NULL, NULL,           P3, "ASUS",        "P4P800SE",              0,   OK, intel_ich_gpio21_raise},
	{0x8086, 0x2570, 0x1043, 0x80b2,  0x8086, 0x24c3, 0x1043, 0x8089, "^P4PE-X/TE$",NULL, NULL,           P3, "ASUS",        "P4PE-X/TE",             0,   NT, intel_ich_gpio21_raise},
	{0x1039, 0x0651, 0x1043, 0x8081,  0x1039, 0x0962,      0,      0, NULL,         NULL, NULL,           P3, "ASUS",        "P4SC-E",                0,   OK, it8707f_write_enable_2e},
	{0x8086, 0x2570, 0x1043, 0x80A5,  0x105A, 0x24D3, 0x1043, 0x80A6, NULL,         NULL, NULL,           P3, "ASUS",        "P4SD-LA",               0,   NT, intel_ich_gpio32_raise},
	{0x1039, 0x0661, 0x1043, 0x8113,  0x1039, 0x5513, 0x1043, 0x8087, NULL,         NULL, NULL,           P3, "ASUS",        "P4S800-MX",             512, OK, w836xx_memw_enable_2e},
	{0x10B9, 0x1541,      0,      0,  0x10B9, 0x1533,      0,      0, "^P5A$",      "asus", "p5a",        P3, "ASUS",        "P5A",                   0,   OK, board_asus_p5a},
	{0x8086, 0x27b8, 0x1043, 0x819e,  0x8086, 0x29f0, 0x1043, 0x82a5, "^P5BV-R$",   NULL, NULL,           P3, "ASUS",        "P5BV-R",                0,   OK, intel_ich_gpio20_raise},
	{0x8086, 0x266a, 0x1043, 0x80a6,  0x8086, 0x2668, 0x1043, 0x814e, "^P5GD1 PRO$", NULL, NULL,          P3, "ASUS",        "P5GD1 Pro",             0,   OK, intel_ich_gpio21_raise},
	{0x8086, 0x266a, 0x1043, 0x80a6,  0x8086, 0x2668, 0x1043, 0x814e, "^P5GD1-VM$", NULL, NULL,           P3, "ASUS",        "P5GD1-VM/S",            0,   OK, intel_ich_gpio21_raise},
	{0x8086, 0x266a, 0x1043, 0x80a6,  0x8086, 0x2668, 0x1043, 0x814e, NULL,         NULL, NULL,           P3, "ASUS",        "P5GD1(-VM)",            0,   NT, intel_ich_gpio21_raise},
	{0x8086, 0x266a, 0x1043, 0x80a6,  0x8086, 0x2668, 0x1043, 0x813d, "^P5GD2-Premium$", NULL, NULL,      P3, "ASUS",        "P5GD2 Premium",         0,   OK, intel_ich_gpio21_raise},
	{0x8086, 0x266a, 0x1043, 0x80a6,  0x8086, 0x2668, 0x1043, 0x81a6, "^P5GD2-X$",  NULL, NULL,           P3, "ASUS",        "P5GD2-X",               0,   OK, intel_ich_gpio21_raise},
	{0x8086, 0x266a, 0x1043, 0x80a6,  0x8086, 0x2668, 0x1043, 0x813d, "^P5GDC-V$",  NULL, NULL,           P3, "ASUS",        "P5GDC-V Deluxe",        0,   OK, intel_ich_gpio21_raise},
	{0x8086, 0x266a, 0x1043, 0x80a6,  0x8086, 0x2668, 0x1043, 0x813d, "^P5GDC$",    NULL, NULL,           P3, "ASUS",        "P5GDC Deluxe",          0,   OK, intel_ich_gpio21_raise},
	{0x8086, 0x266a, 0x1043, 0x80a6,  0x8086, 0x2668, 0x1043, 0x813d, NULL,         NULL, NULL,           P3, "ASUS",        "P5GD2/C variants",      0,   NT, intel_ich_gpio21_raise},
	{0x8086, 0x27b8, 0x103c, 0x2a22,  0x8086, 0x2770, 0x103c, 0x2a22, "^LITHIUM$",  NULL, NULL,           P3, "ASUS",        "P5LP-LE (Lithium-UL8E)",0,   OK, intel_ich_gpio34_raise},
	{0x8086, 0x27b8, 0x1043, 0x2a22,  0x8086, 0x2770, 0x1043, 0x2a22, "^P5LP-LE$",  NULL, NULL,           P3, "ASUS",        "P5LP-LE (Epson OEM)",   0,   OK, intel_ich_gpio34_raise},
	{0x8086, 0x27da, 0x1043, 0x8179,  0x8086, 0x27b8, 0x1043, 0x8179, "^P5LD2$",    NULL, NULL,           P3, "ASUS",        "P5LD2",                 0,   OK, intel_ich_gpio16_raise},
	{0x8086, 0x27da, 0x1043, 0x8179,  0x8086, 0x27b0, 0x1043, 0x8179, "^P5LD2-MQ$", NULL, NULL,           P3, "ASUS",        "P5LD2-MQ",              0,   OK, intel_ich_gpio16_raise},
	{0x8086, 0x27da, 0x1043, 0x8179,  0x8086, 0x27b8, 0x1043, 0x8179, "^P5LD2-VM$", NULL, NULL,           P3, "ASUS",        "P5LD2-VM",              0,   OK, intel_ich_gpio16_raise},
	{0x8086, 0x27b0, 0x1043, 0x8179,  0x8086, 0x2770, 0x1043, 0x817a, "^P5LD2-VM DH$", NULL, NULL,        P3, "ASUS",        "P5LD2-VM DH",           0,   OK, intel_ich_gpio16_raise},
	{0x10DE, 0x0030, 0x1043, 0x818a,  0x8086, 0x100E, 0x1043, 0x80EE, NULL,         NULL, NULL,           P3, "ASUS",        "P5ND2-SLI Deluxe",      0,   OK, nvidia_mcp_gpio10_raise},
	{0x10DE, 0x0260, 0x1043, 0x81BC,  0x10DE, 0x026C, 0x1043, 0x829E, "^P5N-D$",    NULL, NULL,           P3, "ASUS",        "P5N-D",                 0,   OK, it8718f_gpio63_raise},
	{0x10DE, 0x0260, 0x1043, 0x81BC,  0x10DE, 0x026C, 0x1043, 0x8249, "^P5N-E SLI$",NULL, NULL,           P3, "ASUS",        "P5N-E SLI",             0,   NT, it8718f_gpio63_raise},
	{0x8086, 0x24dd, 0x1043, 0x80a6,  0x8086, 0x2570, 0x1043, 0x8157, NULL,         NULL, NULL,           P3, "ASUS",        "P5PE-VM",               0,   OK, intel_ich_gpio21_raise},
	{0x8086, 0x27da, 0x1043, 0x8179,  0x8086, 0x27b8, 0x1043, 0x8179, "^P5W DH Deluxe$", NULL, NULL,      P3, "ASUS",        "P5W DH Deluxe",         0,   OK, intel_ich_gpio16_raise},
	{0x8086, 0x2443, 0x1043, 0x8027,  0x8086, 0x1130, 0x1043, 0x8027, "^CUSL2-C",   NULL, NULL,           P3, "ASUS",        "CUSL2-C",               0,   OK, intel_ich_gpio21_raise},
	{0x8086, 0x2443, 0x1043, 0x8027,  0x8086, 0x1130, 0x1043, 0x8027, "^TUSL2-C",   NULL, NULL,           P3, "ASUS",        "TUSL2-C",               0,   NT, intel_ich_gpio21_raise},
	{0x1022, 0x780E, 0x1043, 0x1437,  0x1022, 0x780B, 0x1043, 0x1437, "^U38N$",     NULL, NULL,           P2, "ASUS",        "U38N",                  0,   OK, p2_whitelist_laptop},
	{0x1106, 0x3059, 0x1106, 0x4161,  0x1106, 0x3065, 0x1106, 0x0102, NULL,         NULL, NULL,           P3, "Bcom/Clientron", "WinNET P680",        0,   OK, w836xx_memw_enable_2e},
	{0x1106, 0x3177, 0x1106, 0x3177,  0x1106, 0x3116, 0x1106, 0x3116, "^KM266-8235$", "biostar", "m7viq", P3, "Biostar",     "M7VIQ",                 0,   NT, w83697xx_memw_enable_2e},
	{0x8086, 0x283e, 0x1028, 0x01f9,  0x8086, 0x2a01,      0,      0, "^Latitude D630", NULL, NULL,       P2, "Dell",        "Latitude D630",         0,   OK, p2_whitelist_laptop},
	{0x10b7, 0x9055, 0x1028, 0x0082,  0x8086, 0x7190,      0,      0, NULL,         NULL, NULL,           P3, "Dell",        "OptiPlex GX1",          0,   OK, intel_piix4_gpo30_lower},
	{0x8086, 0x3590, 0x1028, 0x016c,  0x1000, 0x0030, 0x1028, 0x016c, NULL,         NULL, NULL,           P3, "Dell",        "PowerEdge 1850",        0,   OK, intel_ich_gpio23_raise},
	{0x1106, 0x3189, 0x1106, 0x3189,  0x1106, 0x3177, 0x1106, 0x3177, "^AD77",      "dfi", "ad77",        P3, "DFI",         "AD77",                  0,   NT, w836xx_memw_enable_2e},
	{0x1039, 0x6325, 0x1019, 0x0f05,  0x1039, 0x0016,      0,      0, NULL,         NULL, NULL,           P2, "Elitegroup",  "A928",                  0,   OK, p2_whitelist_laptop},
	{0x10de, 0x03ea, 0x1019, 0x2602,  0x10de, 0x03e0, 0x1019, 0x2602, NULL,         NULL, NULL,           P3, "Elitegroup",  "GeForce6100SM-M",       0,   OK, board_ecs_geforce6100sm_m},
	{0x1106, 0x3038, 0x1019, 0x0996,  0x1106, 0x3177, 0x1019, 0x0996, NULL,         NULL, NULL,           P3, "Elitegroup",  "K7VTA3",                256, OK, NULL},
	{0x1106, 0x3177, 0x1106, 0x3177,  0x1106, 0x3059, 0x1695, 0x3005, NULL,         NULL, NULL,           P3, "EPoX",        "EP-8K5A2",              0,   OK, w836xx_memw_enable_2e},
	{0x10DE, 0x005E, 0x1695, 0x1010,  0x10DE, 0x0050, 0x1695, 0x1010, "8NPA7I",     NULL, NULL,           P3, "EPoX",        "EP-8NPA7I",             0,   OK, nvidia_mcp_gpio4_raise},
	{0x10DE, 0x005E, 0x1695, 0x1010,  0x10DE, 0x0050, 0x1695, 0x1010, "9NPA7I",     NULL, NULL,           P3, "EPoX",        "EP-9NPA7I",             0,   OK, nvidia_mcp_gpio4_raise},
	{0x10EC, 0x8139, 0x1695, 0x9001,  0x11C1, 0x5811, 0x1695, 0x9015, NULL,         NULL, NULL,           P3, "EPoX",        "EP-8RDA3+",             0,   OK, nvidia_mcp_gpio31_raise},
	{0x8086, 0x7110,      0,      0,  0x8086, 0x7190,      0,      0, NULL,         "epox", "ep-bx3",     P3, "EPoX",        "EP-BX3",                0,   NT, intel_piix4_gpo22_raise},
	{0x10de, 0x02f0, 0x105b, 0x0d01,  0x10de, 0x0264, 0x105b, 0x0d01, NULL,         NULL, NULL,           P3, "Foxconn",     "6150K8MD-8EKRSH",       0,   NT, nvidia_mcp_gpio2_raise},
	{0x8086, 0x2A40, 0x1734, 0x1148,  0x8086, 0x2930, 0x1734, 0x1148, "^XY680",     NULL, NULL,           P2, "Fujitsu",     "Amilo Xi 3650",         0,   OK, p2_whitelist_laptop},
	{0x8086, 0x2443, 0x8086, 0x2442,  0x8086, 0x1130, 0x8086, 0x1130, "^6IEM ",     NULL, NULL,           P3, "GIGABYTE",    "GA-6IEM",               0,   NT, intel_ich_gpio25_raise},
	{0x1106, 0x0686, 0x1106, 0x0686,  0x1106, 0x3058, 0x1458, 0xa000, NULL,         NULL, NULL,           P3, "GIGABYTE",    "GA-7ZM",                512, OK, NULL},
	{0x8086, 0x2570, 0x1458, 0x2570,  0x8086, 0x24d0,      0,      0, "^8IP775/-G$",NULL, NULL,           P3, "GIGABYTE",    "GA-8IP775",             0,   OK, intel_ich_gpio32_raise},
	{0x8086, 0x244b, 0x8086, 0x2442,  0x8086, 0x2445, 0x1458, 0xa002, NULL,         NULL, NULL,           P3, "GIGABYTE",    "GA-8IRML",              0,   OK, intel_ich_gpio25_raise},
	{0x8086, 0x24c3, 0x1458, 0x24c2,  0x8086, 0x24cd, 0x1458, 0x5004, NULL,         NULL, NULL,           P3, "GIGABYTE",    "GA-8PE667 Ultra 2",     0,   OK, intel_ich_gpio32_raise},
	{0x1039, 0x0650, 0x1039, 0x0650,  0x1039, 0x7012, 0x1458, 0xA002, "^GA-8SIMLFS20$", NULL, NULL,       P3, "GIGABYTE",    "GA-8SIMLFS 2.0",        0,   OK, sis_gpio0_raise_and_w836xx_memw},
	{0x1039, 0x0651, 0x1039, 0x0651,  0x1039, 0x7002, 0x1458, 0x5004, "^GA-8SIMLH$",NULL, NULL,           P3, "GIGABYTE",    "GA-8SIMLH",             0,   OK, sis_gpio0_raise_and_w836xx_memw},
	{0x10DE, 0x02F1, 0x1458, 0x5000,  0x10DE, 0x0261, 0x1458, 0x5001, NULL,         NULL, NULL,           P3, "GIGABYTE",    "GA-K8N51GMF",           0,   OK, nvidia_mcp_gpio3b_raise},
	{0x10DE, 0x026C, 0x1458, 0xA102,  0x10DE, 0x0260, 0x1458, 0x5001, NULL,         NULL, NULL,           P3, "GIGABYTE",    "GA-K8N51GMF-9",         0,   OK, nvidia_mcp_gpio3b_raise},
	{0x10DE, 0x00E4, 0x1458, 0x0C11,  0x10DE, 0x00E0, 0x1458, 0x0C11, NULL,         NULL, NULL,           P3, "GIGABYTE",    "GA-K8NS",               0,   OK, nvidia_mcp_gpio0a_raise},
	{0x10DE, 0x0050, 0x1458, 0x0C11,  0x10DE, 0x005e, 0x1458, 0x5000, NULL,         NULL, NULL,           P3, "GIGABYTE",    "GA-K8N-SLI",            0,   OK, nvidia_mcp_gpio21_raise},
	{0x8086, 0x2415, 0x103c, 0x1250,  0x10b7, 0x9200, 0x103c, 0x1247, NULL,         NULL, NULL,           P3, "HP",          "e-Vectra P2706T",       0,   OK, board_hp_p2706t},
	{0x1166, 0x0223, 0x103c, 0x320d,  0x14e4, 0x1678, 0x103c, 0x703e, NULL,         "hp", "dl145_g3",     P3, "HP",          "ProLiant DL145 G3",     0,   OK, board_hp_dl145_g3_enable},
	{0x1166, 0x0223, 0x103c, 0x320d,  0x14e4, 0x1648, 0x103c, 0x310f, NULL,         "hp", "dl165_g6",     P3, "HP",          "ProLiant DL165 G6",     0,   OK, board_hp_dl165_g6_enable},
	{0x8086, 0x2580, 0x103c, 0x2a08,  0x8086, 0x2640, 0x103c, 0x2a0a, NULL,         NULL, NULL,           P3, "HP",          "Puffer2-UL8E",          0,   OK, intel_ich_gpio18_raise},
	{0x8086, 0x2415, 0x103c, 0x1249,  0x10b7, 0x9200, 0x103c, 0x1246, NULL,         NULL, NULL,           P3, "HP",          "Vectra VL400",          0,   OK, board_hp_vl400},
	{0x8086, 0x1a30, 0x103c, 0x1a30,  0x8086, 0x2443, 0x103c, 0x2440, "^VL420$",    NULL, NULL,           P3, "HP",          "Vectra VL420 SFF",      0,   OK, intel_ich_gpio22_raise},
	{0x10de, 0x0369, 0x103c, 0x12fe,  0x10de, 0x0364, 0x103c, 0x12fe, NULL,         "hp", "xw9400",       P3, "HP",          "xw9400",                0,   OK, nvidia_mcp_gpio5_raise},
	{0x8086, 0x27A0,      0,      0,  0x8086, 0x27B9,      0,      0, NULL,         "ibase", "mb899",     P3, "IBASE",       "MB899",                 0,   OK, intel_ich_gpio26_raise},
	{0x1166, 0x0205, 0x1014, 0x0347,  0x1002, 0x515E, 0x1014, 0x0325, NULL,         NULL, NULL,           P3, "IBM",         "x3455",                 0,   OK, board_ibm_x3455},
	{0x1039, 0x5513, 0x8086, 0xd61f,  0x1039, 0x6330, 0x8086, 0xd61f, NULL,         NULL, NULL,           P3, "Intel",       "D201GLY",               0,   OK, wbsio_check_for_spi},
	{0x8086, 0x27b8, 0x8086, 0xd606,  0x8086, 0x2770, 0x8086, 0xd606, "^D945GCNL$", NULL, NULL,           P2, "Intel",       "D945GCNL",              0,   OK, p2_not_a_laptop},
	{0x8086, 0x7190,      0,      0,  0x8086, 0x7110,      0,      0, "^SE440BX-2$", NULL, NULL,          P3, "Intel",       "SE440BX-2",             0,   NT, intel_piix4_gpo27_lower},
	{0x1022, 0x7468,      0,      0,  0x1022, 0x7460,      0,      0, NULL,         "iwill", "dk8_htx",   P3, "IWILL",       "DK8-HTX",               0,   OK, w83627hf_gpio24_raise_2e},
	{0x5333, 0x8d04, 0x1106, 0x3065,  0x1106, 0x3059, 0x1106, 0x0571, "P4M266-8235", NULL, NULL,          P3, "Jetway",      "P4MDPT",                0,   OK, w836xx_memw_enable_2e},
	{0x8086, 0x27A0, 0x8086, 0x27a0,  0x8086, 0x27b8, 0x8086, 0x27b8, NULL,        "kontron", "986lcd-m", P3, "Kontron",     "986LCD-M",              0,   OK, board_kontron_986lcd_m},
	{0x8086, 0x2917, 0x17AA, 0x20F5,  0x8086, 0x2930, 0x17AA, 0x20F9, "^ThinkPad R400", NULL, NULL,       P2, "IBM/Lenovo",  "ThinkPad R400",         0,   OK, p2_whitelist_laptop},
	{0x8086, 0x2917, 0x17AA, 0x20F5,  0x8086, 0x2930, 0x17AA, 0x20F9, "^ThinkPad T400", NULL, NULL,       P2, "IBM/Lenovo",  "ThinkPad T400",         0,   OK, p2_whitelist_laptop},
	{0x8086, 0x2917, 0x17AA, 0x20F5,  0x8086, 0x2930, 0x17AA, 0x20F9, "^ThinkPad T500", NULL, NULL,       P2, "IBM/Lenovo",  "ThinkPad T500",         0,   OK, p2_whitelist_laptop},
	{0x8086, 0x1E22, 0x17AA, 0x21F6,  0x8086, 0x1E55, 0x17AA, 0x21F6, "^ThinkPad T530", NULL, NULL,       P2, "IBM/Lenovo",  "ThinkPad T530",         0,   OK, p2_whitelist_laptop},
	{0x8086, 0x27a0, 0x17aa, 0x2015,  0x8086, 0x27b9, 0x17aa, 0x2009, "^ThinkPad T60", NULL, NULL,        P2, "IBM/Lenovo",  "ThinkPad T60",          0,   OK, p2_whitelist_laptop},
	{0x8086, 0x27a0, 0x17aa, 0x2017,  0x8086, 0x27b9, 0x17aa, 0x2009, "^ThinkPad T60", NULL, NULL,        P2, "IBM/Lenovo",  "ThinkPad T60(s)",       0,   OK, p2_whitelist_laptop},
	{0x8086, 0x2917, 0x17AA, 0x20F5,  0x8086, 0x2930, 0x17AA, 0x20F9, "^ThinkPad W500", NULL, NULL,       P2, "IBM/Lenovo",  "ThinkPad W500",         0,   OK, p2_whitelist_laptop},
	{0x8086, 0x2917, 0x17AA, 0x20F5,  0x8086, 0x2930, 0x17AA, 0x20F9, "^ThinkPad X200", NULL, NULL,       P2, "IBM/Lenovo",  "ThinkPad X200",         0,   OK, p2_whitelist_laptop},
	{0x8086, 0x3B07, 0x17AA, 0x2166,  0x8086, 0x3B30, 0x17AA, 0x2167, "^ThinkPad X201", NULL, NULL,       P2, "IBM/Lenovo",  "ThinkPad X201",         0,   OK, p2_whitelist_laptop},
	{0x8086, 0x1C22, 0x17AA, 0x21DB,  0x8086, 0x1C4F, 0x17AA, 0x21DB, NULL, "lenovo", "x220",             P2, "IBM/Lenovo",  "ThinkPad X220",         0,   OK, p2_whitelist_laptop},
	{0x8086, 0x1E22, 0x17AA, 0x21FA,  0x8086, 0x1E55, 0x17AA, 0x21FA, "^ThinkPad X230", NULL, NULL,       P2, "IBM/Lenovo",  "ThinkPad X230",         0,   OK, p2_whitelist_laptop},
	{0x8086, 0x27A0, 0x17AA, 0x2017,  0x8086, 0x27B9, 0x17AA, 0x2009, "^ThinkPad X60", NULL, NULL,        P2, "IBM/Lenovo",  "ThinkPad X60(s)",       0,   OK, p2_whitelist_laptop},
	{0x8086, 0x2917, 0x17AA, 0x20F5,  0x8086, 0x2930, 0x17AA, 0x20F9, "^Taurinus X200", "Libiquity", "Taurinus X200", P2, "Libiquity", "ThinkPad X200", 0, OK, p2_whitelist_laptop},
	{0x8086, 0x2411, 0x8086, 0x2411,  0x8086, 0x7125, 0x0e11, 0xb165, NULL,         NULL, NULL,           P3, "Mitac",       "6513WU",                0,   OK, board_mitac_6513wu},
	{0x8086, 0x8186, 0x8086, 0x8186,  0x8086, 0x8800,      0,      0, "^MSC Vertriebs GmbH$", NULL, NULL, P2, "MSC",         "Q7-TCTC",               0,   OK, p2_not_a_laptop},
	{0x8086, 0x7190,      0,      0,  0x8086, 0x7110,      0,      0, "^MS-6163 (i440BX)$", NULL, NULL,   P3, "MSI",         "MS-6163 (MS-6163 Pro)", 0,   OK, intel_piix4_gpo14_raise},
	{0x8086, 0x244b, 0x1462, 0x3910,  0x8086, 0x2442, 0x1462, 0x3910, NULL,         NULL, NULL,           P3, "MSI",         "MS-6391 (845 Pro4)",    0,   OK, intel_ich_gpio23_raise},
	{0x1039, 0x0745,      0,      0,  0x1039, 0x0018,      0,      0, "^MS-6561",   NULL, NULL,           P3, "MSI",         "MS-6561 (745 Ultra)",   0,   OK, w836xx_memw_enable_2e},
	{0x8086, 0x2560, 0x1462, 0x5770,  0x8086, 0x24C3, 0x1462, 0x5770, NULL,         NULL, NULL,           P3, "MSI",         "MS-6577 (Xenon)",       0,   OK, w83627hf_gpio25_raise_2e},
	{0x13f6, 0x0111, 0x1462, 0x5900,  0x1106, 0x3177, 0x1106,      0, NULL,         NULL, NULL,           P3, "MSI",         "MS-6590 (KT4 Ultra)",   0,   OK, board_msi_kt4v},
	{0x1106, 0x0282, 0x1106, 0x0282,  0x1106, 0x3227, 0x1106, 0x3227, "^MS-7094$",  NULL, NULL,           P3, "MSI",         "MS-7094 (K8T Neo2-F V2.0)", 0, OK, w83627thf_gpio44_raise_2e},
	{0x1106, 0x0571, 0x1462, 0x7120,  0x1106, 0x3065, 0x1462, 0x7120, NULL,         NULL, NULL,           P3, "MSI",         "MS-6712 (KT4V)",        0,   OK, board_msi_kt4v},
	{0x1106, 0x3148, 0     , 0     ,  0x1106, 0x3177, 0     , 0     , NULL,         "msi", "ms6787",      P3, "MSI",         "MS-6787 (P4MAM-V/P4MAM-L)", 0, OK, w836xx_memw_enable_2e},
	{0x8086, 0x24d3, 0x1462, 0x7880,  0x8086, 0x2570,      0,      0, NULL,	        NULL, NULL,           P3, "MSI",         "MS-6788-040 (848P NeoV)", 0, OK, intel_ich_gpio32_raise},
	{0x1039, 0x7012, 0x1462, 0x0050,  0x1039, 0x6325, 0x1462, 0x0058, NULL,         NULL, NULL,           P3, "MSI",         "MS-7005 (651M-L)",      0,   OK, sis_gpio0_raise_and_w836xx_memw},
	{0x10DE, 0x00E0, 0x1462, 0x0250,  0x10DE, 0x00E1, 0x1462, 0x0250, NULL,         NULL, NULL,           P3, "MSI",         "MS-7025 (K8N Neo2 Platinum)", 0, OK, nvidia_mcp_gpio0c_raise},
	{0x10DE, 0x00E0, 0x1462, 0x0300,  0x10DE, 0x00E1, 0x1462, 0x0300, NULL,         NULL, NULL,           P3, "MSI",         "MS-7030 (K8N Neo Platinum)", 0, OK, nvidia_mcp_gpio0c_raise},
	{0x8086, 0x2658, 0x1462, 0x7046,  0x1106, 0x3044, 0x1462, 0x046d, NULL,         NULL, NULL,           P3, "MSI",         "MS-7046",               0,   OK, intel_ich_gpio19_raise},
	{0x1106, 0x3149, 0x1462, 0x7061,  0x1106, 0x3227,      0,      0, NULL,         NULL, NULL,           P3, "MSI",         "MS-7061 (KM4M-V/KM4AM-V)", 0, OK, w836xx_memw_enable_2e},
	{0x10DE, 0x005E, 0x1462, 0x7125,  0x10DE, 0x0052, 0x1462, 0x7125, NULL,         NULL, NULL,           P3, "MSI",         "MS-7125 (K8N Neo4(-F/-FI/-FX/Platinum))", 0, OK, nvidia_mcp_gpio2_raise},
	{0x10DE, 0x005E, 0x1462, 0x7135,  0x10DE, 0x0050, 0x1462, 0x7135, NULL,         "msi", "k8n-neo3",    P3, "MSI",         "MS-7135 (K8N Neo3)",    0,   OK, w83627thf_gpio44_raise_4e},
	{0x10DE, 0x0270, 0x1462, 0x7207,  0x10DE, 0x0264, 0x1462, 0x7207, NULL,         NULL, NULL,           P3, "MSI",         "MS-7207 (K8NGM2-L)",    0,   NT, nvidia_mcp_gpio2_raise},
	{0x10DE, 0x0360, 0x1462, 0x7250,  0x10DE, 0x0368, 0x1462, 0x7250, NULL,         NULL, NULL,           P3, "MSI",         "MS-7250 (K9N SLI)",     0,   OK, nvidia_mcp_gpio2_raise},
	{0x1011, 0x0019, 0xaa55, 0xaa55,  0x8086, 0x7190,      0,      0, NULL,         NULL, NULL,           P3, "Nokia",       "IP530",                 0,   OK, fdc37b787_gpio50_raise_3f0},
	{0x8086, 0x3B30, 0x1025, 0x0379,  0x8086, 0x3B09, 0x1025, 0x0379, "^EasyNote LM85$", NULL, NULL,      P2, "Packard Bell","EasyNote LM85",         0,   OK, p2_whitelist_laptop},
	{0x8086, 0x0154, 0x8086, 0x0154,  0x8086, 0x1e55, 0x8086, 0x1e55, "RV11$",      "Roda", "Lizard RV11", P2, "Roda",       "RV11",                  0,   OK, p2_whitelist_laptop},
	{0x8086, 0x24d3, 0x144d, 0xb025,  0x8086, 0x1050, 0x144d, 0xb025, NULL,         NULL, NULL,           P3, "Samsung",     "Polaris 32",            0,   OK, intel_ich_gpio21_raise},
	{0x1106, 0x3099,      0,      0,  0x1106, 0x3074,      0,      0, NULL,         "shuttle", "ak31",    P3, "Shuttle",     "AK31",                  0,   OK, w836xx_memw_enable_2e},
	{0x1106, 0x3104, 0x1297, 0xa238,  0x1106, 0x3059, 0x1297, 0xc063, NULL,         NULL, NULL,           P3, "Shuttle",     "AK38N",                 256, OK, NULL},
	{0x1106, 0x3038, 0x0925, 0x1234,  0x1106, 0x3058, 0x15DD, 0x7609, NULL,         NULL, NULL,           P3, "Soyo",        "SY-7VCA",               0,   OK, via_apollo_gpo0_lower},
	{0x10de, 0x0364, 0x108e, 0x6676,  0x10de, 0x0369, 0x108e, 0x6676, "^Sun Ultra 40 M2", NULL, NULL,     P3, "Sun",         "Ultra 40 M2",           0,   OK, board_sun_ultra_40_m2},
	{0x1106, 0x3038, 0x0925, 0x1234,  0x1106, 0x0596, 0x1106,      0, NULL,         NULL, NULL,           P3, "Tekram",      "P6Pro-A5",              256, OK, NULL},
	{0x1106, 0x3123, 0x1106, 0x3123,  0x1106, 0x3059, 0x1106, 0x4161, NULL,         NULL, NULL,           P3, "Termtek",     "TK-3370 (Rev:2.5B)",    0,   OK, w836xx_memw_enable_4e},
	{0x8086, 0x7120, 0x109f, 0x3157,  0x8086, 0x2410,      0,      0, NULL,         NULL, NULL,           P3, "TriGem",      "Anaheim-3",             0,   OK, intel_ich_gpio22_raise},
	{0x8086, 0x1076, 0x8086, 0x1176,  0x1106, 0x3059, 0x10f1, 0x2498, NULL,         NULL, NULL,           P3, "Tyan",        "S2498 (Tomcat K7M)",    0,   OK, w836xx_memw_enable_2e},
	{0x1106, 0x0259, 0x1106, 0xAA07,  0x1106, 0x3227, 0x1106, 0xAA07, NULL,         NULL, NULL,           P3, "VIA",         "EPIA EK",               0,   NT, via_vt823x_gpio9_raise},
	{0x1106, 0x3177, 0x1106, 0xAA01,  0x1106, 0x3123, 0x1106, 0xAA01, NULL,         NULL, NULL,           P3, "VIA",         "EPIA M/MII/...",        0,   OK, via_vt823x_gpio15_raise},
	{0x1106, 0x0259, 0x1106, 0x3227,  0x1106, 0x3065, 0x1106, 0x3149, NULL,         NULL, NULL,           P3, "VIA",         "EPIA-N/NL",             0,   OK, via_vt823x_gpio9_raise},
#endif
	{     0,      0,      0,      0,       0,      0,      0,      0, NULL,         NULL, NULL,           P3, NULL,          NULL,                    0,   NT, NULL}, /* end marker */
};

int selfcheck_board_enables(void)
{
	if (board_matches[ARRAY_SIZE(board_matches) - 1].vendor_name != NULL) {
		msg_gerr("Board enables table miscompilation!\n");
		return 1;
	}

	int ret = 0;
	unsigned int i;
	for (i = 0; i + 1 < ARRAY_SIZE(board_matches); i++) {
		const struct board_match *b = &board_matches[i];
		if (b->vendor_name == NULL || b->board_name == NULL) {
			msg_gerr("ERROR: Board enable #%d does not define a vendor and board name.\n"
				 "Please report a bug at flashrom-stable@flashrom.org\n", i);
			ret = 1;
			continue;
		}
		if ((b->first_vendor == 0 || b->first_device == 0 ||
		     b->second_vendor == 0 || b->second_device == 0) ||
		    ((b->lb_vendor == NULL) ^ (b->lb_part == NULL)) ||
		    (b->max_rom_decode_parallel == 0 && b->enable == NULL)) {
			msg_gerr("ERROR: Board enable for %s %s is misdefined.\n"
				 "Please report a bug at flashrom-stable@flashrom.org\n",
				 b->vendor_name, b->board_name);
			ret = 1;
		}
	}
	return ret;
}

/* Parse the <vendor>:<board> string specified by the user as part of -p internal:mainboard=<vendor>:<board>.
 * Parameters vendor and model will be overwritten. Returns 0 on success.
 * Note: strtok modifies the original string, so we work on a copy and allocate memory for the results.
 */
int board_parse_parameter(const char *boardstring, char **vendor, char **model)
{
	/* strtok may modify the original string. */
	char *tempstr = strdup(boardstring);
	char *tempstr2 = NULL;
	strtok(tempstr, ":");
	tempstr2 = strtok(NULL, ":");
	if (tempstr == NULL || tempstr2 == NULL) {
		free(tempstr);
		msg_pinfo("Please supply the board vendor and model name with the "
			  "-p internal:mainboard=<vendor>:<model> option.\n");
		return 1;
	}
	*vendor = strdup(tempstr);
	*model = strdup(tempstr2);
	msg_pspew("-p internal:mainboard: vendor=\"%s\", model=\"%s\"\n", tempstr, tempstr2);
	free(tempstr);
	return 0;
}

/*
 * Match boards on vendor and model name.
 * The string parameters can come either from the coreboot table or the command line (i.e. the user).
 * The boolean needs to be set accordingly to compare them to the right entries of the board enables table.
 * Require main PCI IDs to match too as extra safety.
 * Parameters vendor and model must be non-NULL!
 */
static const struct board_match *board_match_name(const char *vendor, const char *model, bool cb)
{
	const struct board_match *board = board_matches;
	const struct board_match *partmatch = NULL;

	for (; board->vendor_name; board++) {
		const char *cur_vendor = cb ? board->lb_vendor : board->vendor_name;
		const char *cur_model = cb ? board->lb_part : board->board_name;

		if (!cur_vendor || strcasecmp(cur_vendor, vendor))
			continue;

		if (!cur_model || strcasecmp(cur_model, model))
			continue;

		if (!pci_dev_find(board->first_vendor, board->first_device)) {
			msg_pdbg("Odd. Board name \"%s\":\"%s\" matches, but first PCI device %04x:%04x "
				 "doesn't.\n", vendor, model, board->first_vendor, board->first_device);
			continue;
		}

		if (!pci_dev_find(board->second_vendor, board->second_device)) {
			msg_pdbg("Odd. Board name \"%s\":\"%s\" matches, but second PCI device %04x:%04x "
				 "doesn't.\n", vendor, model, board->second_vendor, board->second_device);
			continue;
		}

		if (partmatch) {
			/* More than one entry has a matching name. */
			msg_perr("Board name \"%s\":\"%s\" and PCI IDs matched more than one board enable\n"
				 "entry. Please report a bug at flashrom-stable@flashrom.org\n", vendor, model);
			return NULL;
		}
		partmatch = board;
	}

	if (partmatch)
		return partmatch;

	return NULL;
}

/*
 * Match boards on PCI IDs and subsystem IDs.
 * Second set of IDs can be either main+subsystem IDs, main IDs or no IDs.
 */
static const struct board_match *board_match_pci_ids(enum board_match_phase phase)
{
	const struct board_match *board = board_matches;

	for (; board->vendor_name; board++) {
		if ((!board->first_card_vendor || !board->first_card_device) &&
		      !board->dmi_pattern)
			continue;
		if (board->phase != phase)
			continue;

		if (!pci_card_find(board->first_vendor, board->first_device,
				   board->first_card_vendor,
				   board->first_card_device))
			continue;

		if (board->second_vendor) {
			if (board->second_card_vendor) {
				if (!pci_card_find(board->second_vendor,
						   board->second_device,
						   board->second_card_vendor,
						   board->second_card_device))
					continue;
			} else {
				if (!pci_dev_find(board->second_vendor,
						  board->second_device))
					continue;
			}
		}

#if defined(__i386__) || defined(__x86_64__)
		if (board->dmi_pattern) {
			if (!has_dmi_support) {
				msg_pwarn("Warning: Can't autodetect %s %s, DMI info unavailable.\n",
					  board->vendor_name, board->board_name);
				msg_pinfo("Please supply the board vendor and model name with the "
					  "-p internal:mainboard=<vendor>:<model> option.\n");
				continue;
			} else {
				if (!dmi_match(board->dmi_pattern))
					continue;
			}
		}
#endif // defined(__i386__) || defined(__x86_64__)
		return board;
	}

	return NULL;
}

static int board_enable_safetycheck(const struct board_match *board)
{
	if (!board)
		return 1;

	if (board->status == OK)
		return 0;

	if (!force_boardenable) {
		msg_pwarn("Warning: The mainboard-specific code for %s %s has not been tested,\n"
			  "and thus will not be executed by default. Depending on your hardware,\n"
			  "erasing, writing or even probing can fail without running this code.\n\n"
			  "Please see the man page (section PROGRAMMER SPECIFIC INFO, subsection\n"
			  "\"internal programmer\") for details.\n", board->vendor_name, board->board_name);
		return 1;
	}
	msg_pwarn("NOTE: Running an untested board enable procedure.\n"
		  "Please report success/failure to flashrom-stable@flashrom.org.\n");
	return 0;
}

/* FIXME: Should this be identical to board_flash_enable? */
static int board_handle_phase(enum board_match_phase phase)
{
	const struct board_match *board = NULL;

	board = board_match_pci_ids(phase);

	if (!board)
		return 0;

	if (board_enable_safetycheck(board))
		return 0;

	if (!board->enable) {
		/* Not sure if there is a valid case for this. */
		msg_perr("Board match found, but nothing to do?\n");
		return 0;
	}

	return board->enable();
}

void board_handle_before_superio(void)
{
	board_handle_phase(P1);
}

void board_handle_before_laptop(void)
{
	board_handle_phase(P2);
}

int board_flash_enable(const char *vendor, const char *model, const char *cb_vendor, const char *cb_model)
{
	const struct board_match *board = NULL;
	int ret = 0;

	if (vendor != NULL  && model != NULL) {
		board = board_match_name(vendor, model, false);
		if (!board) { /* If a board was given by the user it has to match, else we abort here. */
			msg_perr("No suitable board enable found for vendor=\"%s\", model=\"%s\".\n",
				 vendor, model);
			return 1;
		}
	}
	if (board == NULL && cb_vendor != NULL && cb_model != NULL) {
		board = board_match_name(cb_vendor, cb_model, true);
		if (!board) { /* Failure is an option here, because many cb boards don't require an enable. */
			msg_pdbg2("No board enable found matching coreboot IDs vendor=\"%s\", model=\"%s\".\n",
				  cb_vendor, cb_model);
		}
	}
	if (board == NULL) {
		board = board_match_pci_ids(P3);
		if (!board) /* i.e. there is just no board enable available for this board */
			return 0;
	}

	if (board_enable_safetycheck(board))
		return 1;

	/* limit the maximum size of the parallel bus */
	if (board->max_rom_decode_parallel)
		max_rom_decode.parallel = board->max_rom_decode_parallel * 1024;

	if (board->enable != NULL) {
		msg_pinfo("Enabling full flash access for board \"%s %s\"... ",
			  board->vendor_name, board->board_name);

		ret = board->enable();
		if (ret)
			msg_pinfo("FAILED!\n");
		else
			msg_pinfo("OK.\n");
	}

	return ret;
}