| /* |
| * This file is part of the flashrom project. |
| * |
| * Copyright (C) 2000 Silicon Integrated System Corporation |
| * Copyright (C) 2005-2009 coresystems GmbH |
| * Copyright (C) 2006 Uwe Hermann <uwe@hermann-uwe.de> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; version 2 of the License. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA |
| */ |
| |
| /* |
| * Contains the chipset specific flash enables. |
| */ |
| |
| #define _LARGEFILE64_SOURCE |
| |
| #include <stdlib.h> |
| #include <string.h> |
| #include <sys/types.h> |
| #include <sys/stat.h> |
| #include <fcntl.h> |
| #include "flash.h" |
| |
| unsigned long flashbase = 0; |
| |
| /** |
| * flashrom defaults to Parallel/LPC/FWH flash devices. If a known host |
| * controller is found, the init routine sets the buses_supported bitfield to |
| * contain the supported buses for that controller. |
| */ |
| |
| enum chipbustype buses_supported = CHIP_BUSTYPE_NONSPI; |
| |
| extern int ichspi_lock; |
| |
| static int enable_flash_ali_m1533(struct pci_dev *dev, const char *name) |
| { |
| uint8_t tmp; |
| |
| /* |
| * ROM Write enable, 0xFFFC0000-0xFFFDFFFF and |
| * 0xFFFE0000-0xFFFFFFFF ROM select enable. |
| */ |
| tmp = pci_read_byte(dev, 0x47); |
| tmp |= 0x46; |
| pci_write_byte(dev, 0x47, tmp); |
| |
| return 0; |
| } |
| |
| static int enable_flash_sis630(struct pci_dev *dev, const char *name) |
| { |
| uint8_t b; |
| |
| /* Enable 0xFFF8000~0xFFFF0000 decoding on SiS 540/630. */ |
| b = pci_read_byte(dev, 0x40); |
| pci_write_byte(dev, 0x40, b | 0xb); |
| |
| /* Flash write enable on SiS 540/630. */ |
| b = pci_read_byte(dev, 0x45); |
| pci_write_byte(dev, 0x45, b | 0x40); |
| |
| /* The same thing on SiS 950 Super I/O side... */ |
| |
| /* First probe for Super I/O on config port 0x2e. */ |
| OUTB(0x87, 0x2e); |
| OUTB(0x01, 0x2e); |
| OUTB(0x55, 0x2e); |
| OUTB(0x55, 0x2e); |
| |
| if (INB(0x2f) != 0x87) { |
| /* If that failed, try config port 0x4e. */ |
| OUTB(0x87, 0x4e); |
| OUTB(0x01, 0x4e); |
| OUTB(0x55, 0x4e); |
| OUTB(0xaa, 0x4e); |
| if (INB(0x4f) != 0x87) { |
| printf("Can not access SiS 950\n"); |
| return -1; |
| } |
| OUTB(0x24, 0x4e); |
| b = INB(0x4f) | 0xfc; |
| OUTB(0x24, 0x4e); |
| OUTB(b, 0x4f); |
| OUTB(0x02, 0x4e); |
| OUTB(0x02, 0x4f); |
| } |
| |
| OUTB(0x24, 0x2e); |
| printf_debug("2f is %#x\n", INB(0x2f)); |
| b = INB(0x2f) | 0xfc; |
| OUTB(0x24, 0x2e); |
| OUTB(b, 0x2f); |
| |
| OUTB(0x02, 0x2e); |
| OUTB(0x02, 0x2f); |
| |
| return 0; |
| } |
| |
| /* Datasheet: |
| * - Name: 82371AB PCI-TO-ISA / IDE XCELERATOR (PIIX4) |
| * - URL: http://www.intel.com/design/intarch/datashts/290562.htm |
| * - PDF: http://www.intel.com/design/intarch/datashts/29056201.pdf |
| * - Order Number: 290562-001 |
| */ |
| static int enable_flash_piix4(struct pci_dev *dev, const char *name) |
| { |
| uint16_t old, new; |
| uint16_t xbcs = 0x4e; /* X-Bus Chip Select register. */ |
| |
| old = pci_read_word(dev, xbcs); |
| |
| /* Set bit 9: 1-Meg Extended BIOS Enable (PCI master accesses to |
| * FFF00000-FFF7FFFF are forwarded to ISA). |
| * Note: This bit is reserved on PIIX/PIIX3/MPIIX. |
| * Set bit 7: Extended BIOS Enable (PCI master accesses to |
| * FFF80000-FFFDFFFF are forwarded to ISA). |
| * Set bit 6: Lower BIOS Enable (PCI master, or ISA master accesses to |
| * the lower 64-Kbyte BIOS block (E0000-EFFFF) at the top |
| * of 1 Mbyte, or the aliases at the top of 4 Gbyte |
| * (FFFE0000-FFFEFFFF) result in the generation of BIOSCS#. |
| * Note: Accesses to FFFF0000-FFFFFFFF are always forwarded to ISA. |
| * Set bit 2: BIOSCS# Write Enable (1=enable, 0=disable). |
| */ |
| if (dev->device_id == 0x122e || dev->device_id == 0x7000 |
| || dev->device_id == 0x1234) |
| new = old | 0x00c4; /* PIIX/PIIX3/MPIIX: Bit 9 is reserved. */ |
| else |
| new = old | 0x02c4; |
| |
| if (new == old) |
| return 0; |
| |
| pci_write_word(dev, xbcs, new); |
| |
| if (pci_read_word(dev, xbcs) != new) { |
| printf_debug("tried to set 0x%x to 0x%x on %s failed (WARNING ONLY)\n", xbcs, new, name); |
| return -1; |
| } |
| |
| return 0; |
| } |
| |
| /* |
| * See ie. page 375 of "Intel I/O Controller Hub 7 (ICH7) Family Datasheet" |
| * http://download.intel.com/design/chipsets/datashts/30701303.pdf |
| */ |
| static int enable_flash_ich(struct pci_dev *dev, const char *name, |
| int bios_cntl) |
| { |
| uint8_t old, new; |
| |
| /* |
| * Note: the ICH0-ICH5 BIOS_CNTL register is actually 16 bit wide, but |
| * just treating it as 8 bit wide seems to work fine in practice. |
| */ |
| old = pci_read_byte(dev, bios_cntl); |
| |
| printf_debug("\nBIOS Lock Enable: %sabled, ", |
| (old & (1 << 1)) ? "en" : "dis"); |
| printf_debug("BIOS Write Enable: %sabled, ", |
| (old & (1 << 0)) ? "en" : "dis"); |
| printf_debug("BIOS_CNTL is 0x%x\n", old); |
| |
| new = old | 1; |
| |
| if (new == old) |
| return 0; |
| |
| pci_write_byte(dev, bios_cntl, new); |
| |
| if (pci_read_byte(dev, bios_cntl) != new) { |
| printf_debug("tried to set 0x%x to 0x%x on %s failed (WARNING ONLY)\n", bios_cntl, new, name); |
| return -1; |
| } |
| |
| return 0; |
| } |
| |
| static int enable_flash_ich_4e(struct pci_dev *dev, const char *name) |
| { |
| /* |
| * Note: ICH5 has registers similar to FWH_SEL1, FWH_SEL2 and |
| * FWH_DEC_EN1, but they are called FB_SEL1, FB_SEL2, FB_DEC_EN1 and |
| * FB_DEC_EN2. |
| */ |
| return enable_flash_ich(dev, name, 0x4e); |
| } |
| |
| static int enable_flash_ich_dc(struct pci_dev *dev, const char *name) |
| { |
| uint32_t fwh_conf; |
| int i; |
| |
| /* Ignore all legacy ranges below 1 MB. */ |
| /* FWH_SEL1 */ |
| fwh_conf = pci_read_long(dev, 0xd0); |
| for (i = 7; i >= 0; i--) |
| printf_debug("\n0x%08x/0x%08x FWH IDSEL: 0x%x", |
| (0x1ff8 + i) * 0x80000, |
| (0x1ff0 + i) * 0x80000, |
| (fwh_conf >> (i * 4)) & 0xf); |
| /* FWH_SEL2 */ |
| fwh_conf = pci_read_word(dev, 0xd4); |
| for (i = 3; i >= 0; i--) |
| printf_debug("\n0x%08x/0x%08x FWH IDSEL: 0x%x", |
| (0xff4 + i) * 0x100000, |
| (0xff0 + i) * 0x100000, |
| (fwh_conf >> (i * 4)) & 0xf); |
| /* FWH_DEC_EN1 */ |
| fwh_conf = pci_read_word(dev, 0xd8); |
| for (i = 7; i >= 0; i--) |
| printf_debug("\n0x%08x/0x%08x FWH decode %sabled", |
| (0x1ff8 + i) * 0x80000, |
| (0x1ff0 + i) * 0x80000, |
| (fwh_conf >> (i + 0x8)) & 0x1 ? "en" : "dis"); |
| for (i = 3; i >= 0; i--) |
| printf_debug("\n0x%08x/0x%08x FWH decode %sabled", |
| (0xff4 + i) * 0x100000, |
| (0xff0 + i) * 0x100000, |
| (fwh_conf >> i) & 0x1 ? "en" : "dis"); |
| |
| return enable_flash_ich(dev, name, 0xdc); |
| } |
| |
| #define ICH_STRAP_RSVD 0x00 |
| #define ICH_STRAP_SPI 0x01 |
| #define ICH_STRAP_PCI 0x02 |
| #define ICH_STRAP_LPC 0x03 |
| |
| static int enable_flash_vt8237s_spi(struct pci_dev *dev, const char *name) |
| { |
| uint32_t mmio_base; |
| |
| mmio_base = (pci_read_long(dev, 0xbc)) << 8; |
| printf_debug("MMIO base at = 0x%x\n", mmio_base); |
| spibar = physmap("VT8237S MMIO registers", mmio_base, 0x70); |
| |
| printf_debug("0x6c: 0x%04x (CLOCK/DEBUG)\n", |
| mmio_readw(spibar + 0x6c)); |
| |
| /* Not sure if it speaks all these bus protocols. */ |
| buses_supported = CHIP_BUSTYPE_LPC | CHIP_BUSTYPE_FWH | CHIP_BUSTYPE_SPI; |
| spi_controller = SPI_CONTROLLER_VIA; |
| ich_init_opcodes(); |
| |
| return 0; |
| } |
| |
| static int enable_flash_ich_dc_spi(struct pci_dev *dev, const char *name, |
| int ich_generation) |
| { |
| int ret, i; |
| uint8_t old, new, bbs, buc; |
| uint16_t spibar_offset, tmp2; |
| uint32_t tmp, gcs; |
| void *rcrb; |
| //TODO: These names are incorrect for EP80579. For that, the solution would look like the commented line |
| //static const char *straps_names[] = {"SPI", "reserved", "reserved", "LPC" }; |
| static const char *straps_names[] = { "reserved", "SPI", "PCI", "LPC" }; |
| |
| /* Enable Flash Writes */ |
| ret = enable_flash_ich_dc(dev, name); |
| |
| /* Get physical address of Root Complex Register Block */ |
| tmp = pci_read_long(dev, 0xf0) & 0xffffc000; |
| printf_debug("\nRoot Complex Register Block address = 0x%x\n", tmp); |
| |
| /* Map RCBA to virtual memory */ |
| rcrb = physmap("ICH RCRB", tmp, 0x4000); |
| |
| gcs = mmio_readl(rcrb + 0x3410); |
| printf_debug("GCS = 0x%x: ", gcs); |
| printf_debug("BIOS Interface Lock-Down: %sabled, ", |
| (gcs & 0x1) ? "en" : "dis"); |
| bbs = (gcs >> 10) & 0x3; |
| printf_debug("BOOT BIOS Straps: 0x%x (%s)\n", bbs, straps_names[bbs]); |
| |
| buc = mmio_readb(rcrb + 0x3414); |
| printf_debug("Top Swap : %s\n", |
| (buc & 1) ? "enabled (A16 inverted)" : "not enabled"); |
| |
| /* It seems the ICH7 does not support SPI and LPC chips at the same |
| * time. At least not with our current code. So we prevent searching |
| * on ICH7 when the southbridge is strapped to LPC |
| */ |
| |
| if (ich_generation == 7 && bbs == ICH_STRAP_LPC) { |
| /* Not sure if it speaks LPC as well. */ |
| buses_supported = CHIP_BUSTYPE_LPC | CHIP_BUSTYPE_FWH; |
| /* No further SPI initialization required */ |
| return ret; |
| } |
| |
| switch (ich_generation) { |
| case 7: |
| buses_supported = CHIP_BUSTYPE_SPI; |
| spi_controller = SPI_CONTROLLER_ICH7; |
| spibar_offset = 0x3020; |
| break; |
| case 8: |
| /* Not sure if it speaks LPC as well. */ |
| buses_supported = CHIP_BUSTYPE_LPC | CHIP_BUSTYPE_FWH | CHIP_BUSTYPE_SPI; |
| spi_controller = SPI_CONTROLLER_ICH9; |
| spibar_offset = 0x3020; |
| break; |
| case 9: |
| case 10: |
| default: /* Future version might behave the same */ |
| /* Not sure if it speaks LPC as well. */ |
| buses_supported = CHIP_BUSTYPE_LPC | CHIP_BUSTYPE_FWH | CHIP_BUSTYPE_SPI; |
| spi_controller = SPI_CONTROLLER_ICH9; |
| spibar_offset = 0x3800; |
| break; |
| } |
| |
| /* SPIBAR is at RCRB+0x3020 for ICH[78] and RCRB+0x3800 for ICH9. */ |
| printf_debug("SPIBAR = 0x%x + 0x%04x\n", tmp, spibar_offset); |
| |
| /* Assign Virtual Address */ |
| spibar = rcrb + spibar_offset; |
| |
| switch (spi_controller) { |
| case SPI_CONTROLLER_ICH7: |
| printf_debug("0x00: 0x%04x (SPIS)\n", |
| mmio_readw(spibar + 0)); |
| printf_debug("0x02: 0x%04x (SPIC)\n", |
| mmio_readw(spibar + 2)); |
| printf_debug("0x04: 0x%08x (SPIA)\n", |
| mmio_readl(spibar + 4)); |
| for (i = 0; i < 8; i++) { |
| int offs; |
| offs = 8 + (i * 8); |
| printf_debug("0x%02x: 0x%08x (SPID%d)\n", offs, |
| mmio_readl(spibar + offs), i); |
| printf_debug("0x%02x: 0x%08x (SPID%d+4)\n", offs + 4, |
| mmio_readl(spibar + offs + 4), i); |
| } |
| printf_debug("0x50: 0x%08x (BBAR)\n", |
| mmio_readl(spibar + 0x50)); |
| printf_debug("0x54: 0x%04x (PREOP)\n", |
| mmio_readw(spibar + 0x54)); |
| printf_debug("0x56: 0x%04x (OPTYPE)\n", |
| mmio_readw(spibar + 0x56)); |
| printf_debug("0x58: 0x%08x (OPMENU)\n", |
| mmio_readl(spibar + 0x58)); |
| printf_debug("0x5c: 0x%08x (OPMENU+4)\n", |
| mmio_readl(spibar + 0x5c)); |
| for (i = 0; i < 4; i++) { |
| int offs; |
| offs = 0x60 + (i * 4); |
| printf_debug("0x%02x: 0x%08x (PBR%d)\n", offs, |
| mmio_readl(spibar + offs), i); |
| } |
| printf_debug("\n"); |
| if (mmio_readw(spibar) & (1 << 15)) { |
| printf("WARNING: SPI Configuration Lockdown activated.\n"); |
| ichspi_lock = 1; |
| } |
| ich_init_opcodes(); |
| break; |
| case SPI_CONTROLLER_ICH9: |
| tmp2 = mmio_readw(spibar + 4); |
| printf_debug("0x04: 0x%04x (HSFS)\n", tmp2); |
| printf_debug("FLOCKDN %i, ", (tmp2 >> 15 & 1)); |
| printf_debug("FDV %i, ", (tmp2 >> 14) & 1); |
| printf_debug("FDOPSS %i, ", (tmp2 >> 13) & 1); |
| printf_debug("SCIP %i, ", (tmp2 >> 5) & 1); |
| printf_debug("BERASE %i, ", (tmp2 >> 3) & 3); |
| printf_debug("AEL %i, ", (tmp2 >> 2) & 1); |
| printf_debug("FCERR %i, ", (tmp2 >> 1) & 1); |
| printf_debug("FDONE %i\n", (tmp2 >> 0) & 1); |
| |
| tmp = mmio_readl(spibar + 0x50); |
| printf_debug("0x50: 0x%08x (FRAP)\n", tmp); |
| printf_debug("BMWAG %i, ", (tmp >> 24) & 0xff); |
| printf_debug("BMRAG %i, ", (tmp >> 16) & 0xff); |
| printf_debug("BRWA %i, ", (tmp >> 8) & 0xff); |
| printf_debug("BRRA %i\n", (tmp >> 0) & 0xff); |
| |
| printf_debug("0x54: 0x%08x (FREG0)\n", |
| mmio_readl(spibar + 0x54)); |
| printf_debug("0x58: 0x%08x (FREG1)\n", |
| mmio_readl(spibar + 0x58)); |
| printf_debug("0x5C: 0x%08x (FREG2)\n", |
| mmio_readl(spibar + 0x5C)); |
| printf_debug("0x60: 0x%08x (FREG3)\n", |
| mmio_readl(spibar + 0x60)); |
| printf_debug("0x64: 0x%08x (FREG4)\n", |
| mmio_readl(spibar + 0x64)); |
| printf_debug("0x74: 0x%08x (PR0)\n", |
| mmio_readl(spibar + 0x74)); |
| printf_debug("0x78: 0x%08x (PR1)\n", |
| mmio_readl(spibar + 0x78)); |
| printf_debug("0x7C: 0x%08x (PR2)\n", |
| mmio_readl(spibar + 0x7C)); |
| printf_debug("0x80: 0x%08x (PR3)\n", |
| mmio_readl(spibar + 0x80)); |
| printf_debug("0x84: 0x%08x (PR4)\n", |
| mmio_readl(spibar + 0x84)); |
| printf_debug("0x90: 0x%08x (SSFS, SSFC)\n", |
| mmio_readl(spibar + 0x90)); |
| printf_debug("0x94: 0x%04x (PREOP)\n", |
| mmio_readw(spibar + 0x94)); |
| printf_debug("0x96: 0x%04x (OPTYPE)\n", |
| mmio_readw(spibar + 0x96)); |
| printf_debug("0x98: 0x%08x (OPMENU)\n", |
| mmio_readl(spibar + 0x98)); |
| printf_debug("0x9C: 0x%08x (OPMENU+4)\n", |
| mmio_readl(spibar + 0x9C)); |
| printf_debug("0xA0: 0x%08x (BBAR)\n", |
| mmio_readl(spibar + 0xA0)); |
| printf_debug("0xB0: 0x%08x (FDOC)\n", |
| mmio_readl(spibar + 0xB0)); |
| if (tmp2 & (1 << 15)) { |
| printf("WARNING: SPI Configuration Lockdown activated.\n"); |
| ichspi_lock = 1; |
| } |
| ich_init_opcodes(); |
| break; |
| default: |
| /* Nothing */ |
| break; |
| } |
| |
| old = pci_read_byte(dev, 0xdc); |
| printf_debug("SPI Read Configuration: "); |
| new = (old >> 2) & 0x3; |
| switch (new) { |
| case 0: |
| case 1: |
| case 2: |
| printf_debug("prefetching %sabled, caching %sabled, ", |
| (new & 0x2) ? "en" : "dis", |
| (new & 0x1) ? "dis" : "en"); |
| break; |
| default: |
| printf_debug("invalid prefetching/caching settings, "); |
| break; |
| } |
| |
| return ret; |
| } |
| |
| static int enable_flash_ich7(struct pci_dev *dev, const char *name) |
| { |
| return enable_flash_ich_dc_spi(dev, name, 7); |
| } |
| |
| static int enable_flash_ich8(struct pci_dev *dev, const char *name) |
| { |
| return enable_flash_ich_dc_spi(dev, name, 8); |
| } |
| |
| static int enable_flash_ich9(struct pci_dev *dev, const char *name) |
| { |
| return enable_flash_ich_dc_spi(dev, name, 9); |
| } |
| |
| static int enable_flash_ich10(struct pci_dev *dev, const char *name) |
| { |
| return enable_flash_ich_dc_spi(dev, name, 10); |
| } |
| |
| static int enable_flash_vt823x(struct pci_dev *dev, const char *name) |
| { |
| uint8_t val; |
| |
| /* enable ROM decode range (1MB) FFC00000 - FFFFFFFF */ |
| pci_write_byte(dev, 0x41, 0x7f); |
| |
| /* ROM write enable */ |
| val = pci_read_byte(dev, 0x40); |
| val |= 0x10; |
| pci_write_byte(dev, 0x40, val); |
| |
| if (pci_read_byte(dev, 0x40) != val) { |
| printf("\nWARNING: Failed to enable flash write on \"%s\"\n", |
| name); |
| return -1; |
| } |
| |
| return 0; |
| } |
| |
| static int enable_flash_cs5530(struct pci_dev *dev, const char *name) |
| { |
| uint8_t reg8; |
| |
| #define DECODE_CONTROL_REG2 0x5b /* F0 index 0x5b */ |
| #define ROM_AT_LOGIC_CONTROL_REG 0x52 /* F0 index 0x52 */ |
| |
| #define LOWER_ROM_ADDRESS_RANGE (1 << 0) |
| #define ROM_WRITE_ENABLE (1 << 1) |
| #define UPPER_ROM_ADDRESS_RANGE (1 << 2) |
| #define BIOS_ROM_POSITIVE_DECODE (1 << 5) |
| |
| /* Decode 0x000E0000-0x000FFFFF (128 KB), not just 64 KB, and |
| * decode 0xFF000000-0xFFFFFFFF (16 MB), not just 256 KB. |
| * Make the configured ROM areas writable. |
| */ |
| reg8 = pci_read_byte(dev, ROM_AT_LOGIC_CONTROL_REG); |
| reg8 |= LOWER_ROM_ADDRESS_RANGE; |
| reg8 |= UPPER_ROM_ADDRESS_RANGE; |
| reg8 |= ROM_WRITE_ENABLE; |
| pci_write_byte(dev, ROM_AT_LOGIC_CONTROL_REG, reg8); |
| |
| /* Set positive decode on ROM. */ |
| reg8 = pci_read_byte(dev, DECODE_CONTROL_REG2); |
| reg8 |= BIOS_ROM_POSITIVE_DECODE; |
| pci_write_byte(dev, DECODE_CONTROL_REG2, reg8); |
| |
| return 0; |
| } |
| |
| /** |
| * Geode systems write protect the BIOS via RCONFs (cache settings similar |
| * to MTRRs). To unlock, change MSR 0x1808 top byte to 0x22. |
| * |
| * Geode systems also write protect the NOR flash chip itself via MSR_NORF_CTL. |
| * To enable write to NOR Boot flash for the benefit of systems that have such |
| * a setup, raise MSR 0x51400018 WE_CS3 (write enable Boot Flash Chip Select). |
| */ |
| static int enable_flash_cs5536(struct pci_dev *dev, const char *name) |
| { |
| #define MSR_RCONF_DEFAULT 0x1808 |
| #define MSR_NORF_CTL 0x51400018 |
| |
| msr_t msr; |
| |
| /* Geode only has a single core */ |
| if (setup_cpu_msr(0)) |
| return -1; |
| |
| msr = rdmsr(MSR_RCONF_DEFAULT); |
| if ((msr.hi >> 24) != 0x22) { |
| msr.hi &= 0xfbffffff; |
| wrmsr(MSR_RCONF_DEFAULT, msr); |
| } |
| |
| msr = rdmsr(MSR_NORF_CTL); |
| /* Raise WE_CS3 bit. */ |
| msr.lo |= 0x08; |
| wrmsr(MSR_NORF_CTL, msr); |
| |
| cleanup_cpu_msr(); |
| |
| #undef MSR_RCONF_DEFAULT |
| #undef MSR_NORF_CTL |
| return 0; |
| } |
| |
| static int enable_flash_sc1100(struct pci_dev *dev, const char *name) |
| { |
| uint8_t new; |
| |
| pci_write_byte(dev, 0x52, 0xee); |
| |
| new = pci_read_byte(dev, 0x52); |
| |
| if (new != 0xee) { |
| printf_debug("tried to set register 0x%x to 0x%x on %s failed (WARNING ONLY)\n", 0x52, new, name); |
| return -1; |
| } |
| |
| return 0; |
| } |
| |
| static int enable_flash_sis5595(struct pci_dev *dev, const char *name) |
| { |
| uint8_t new, newer; |
| |
| new = pci_read_byte(dev, 0x45); |
| |
| new &= (~0x20); /* Clear bit 5. */ |
| new |= 0x4; /* Set bit 2. */ |
| |
| pci_write_byte(dev, 0x45, new); |
| |
| newer = pci_read_byte(dev, 0x45); |
| if (newer != new) { |
| printf_debug("tried to set register 0x%x to 0x%x on %s failed (WARNING ONLY)\n", 0x45, new, name); |
| printf_debug("Stuck at 0x%x\n", newer); |
| return -1; |
| } |
| |
| /* Extended BIOS enable = 1, Lower BIOS Enable = 1 */ |
| new = pci_read_byte(dev, 0x40); |
| new &= 0xFB; |
| new |= 0x3; |
| pci_write_byte(dev, 0x40, new); |
| newer = pci_read_byte(dev, 0x40); |
| if (newer != new) { |
| printf_debug("tried to set register 0x%x to 0x%x on %s failed (WARNING ONLY)\n", 0x40, new, name); |
| printf_debug("Stuck at 0x%x\n", newer); |
| return -1; |
| } |
| return 0; |
| } |
| |
| /* Works for AMD-8111, VIA VT82C586A/B, VIA VT82C686A/B. */ |
| static int enable_flash_amd8111(struct pci_dev *dev, const char *name) |
| { |
| uint8_t old, new; |
| |
| /* Enable decoding at 0xffb00000 to 0xffffffff. */ |
| old = pci_read_byte(dev, 0x43); |
| new = old | 0xC0; |
| if (new != old) { |
| pci_write_byte(dev, 0x43, new); |
| if (pci_read_byte(dev, 0x43) != new) { |
| printf_debug("tried to set 0x%x to 0x%x on %s failed (WARNING ONLY)\n", 0x43, new, name); |
| } |
| } |
| |
| /* Enable 'ROM write' bit. */ |
| old = pci_read_byte(dev, 0x40); |
| new = old | 0x01; |
| if (new == old) |
| return 0; |
| pci_write_byte(dev, 0x40, new); |
| |
| if (pci_read_byte(dev, 0x40) != new) { |
| printf_debug("tried to set 0x%x to 0x%x on %s failed (WARNING ONLY)\n", 0x40, new, name); |
| return -1; |
| } |
| |
| return 0; |
| } |
| |
| static int enable_flash_sb600(struct pci_dev *dev, const char *name) |
| { |
| uint32_t tmp, prot; |
| uint8_t reg; |
| struct pci_dev *smbus_dev; |
| int has_spi = 1; |
| |
| /* Clear ROM protect 0-3. */ |
| for (reg = 0x50; reg < 0x60; reg += 4) { |
| prot = pci_read_long(dev, reg); |
| /* No protection flags for this region?*/ |
| if ((prot & 0x3) == 0) |
| continue; |
| printf_debug("SB600 %s%sprotected from %u to %u\n", |
| (prot & 0x1) ? "write " : "", |
| (prot & 0x2) ? "read " : "", |
| (prot & 0xfffffc00), |
| (prot & 0xfffffc00) + ((prot & 0x3ff) << 8)); |
| prot &= 0xfffffffc; |
| pci_write_byte(dev, reg, prot); |
| prot = pci_read_long(dev, reg); |
| if (prot & 0x3) |
| printf("SB600 %s%sunprotect failed from %u to %u\n", |
| (prot & 0x1) ? "write " : "", |
| (prot & 0x2) ? "read " : "", |
| (prot & 0xfffffc00), |
| (prot & 0xfffffc00) + ((prot & 0x3ff) << 8)); |
| } |
| |
| /* Read SPI_BaseAddr */ |
| tmp = pci_read_long(dev, 0xa0); |
| tmp &= 0xffffffe0; /* remove bits 4-0 (reserved) */ |
| printf_debug("SPI base address is at 0x%x\n", tmp); |
| |
| /* If the BAR has address 0, it is unlikely SPI is used. */ |
| if (!tmp) |
| has_spi = 0; |
| |
| if (has_spi) { |
| /* Physical memory has to be mapped at page (4k) boundaries. */ |
| sb600_spibar = physmap("SB600 SPI registers", tmp & 0xfffff000, |
| 0x1000); |
| /* The low bits of the SPI base address are used as offset into |
| * the mapped page. |
| */ |
| sb600_spibar += tmp & 0xfff; |
| |
| tmp = pci_read_long(dev, 0xa0); |
| printf_debug("AltSpiCSEnable=%i, SpiRomEnable=%i, " |
| "AbortEnable=%i\n", tmp & 0x1, (tmp & 0x2) >> 1, |
| (tmp & 0x4) >> 2); |
| tmp = (pci_read_byte(dev, 0xba) & 0x4) >> 2; |
| printf_debug("PrefetchEnSPIFromIMC=%i, ", tmp); |
| |
| tmp = pci_read_byte(dev, 0xbb); |
| printf_debug("PrefetchEnSPIFromHost=%i, SpiOpEnInLpcMode=%i\n", |
| tmp & 0x1, (tmp & 0x20) >> 5); |
| tmp = mmio_readl(sb600_spibar); |
| printf_debug("SpiArbEnable=%i, SpiAccessMacRomEn=%i, " |
| "SpiHostAccessRomEn=%i, ArbWaitCount=%i, " |
| "SpiBridgeDisable=%i, DropOneClkOnRd=%i\n", |
| (tmp >> 19) & 0x1, (tmp >> 22) & 0x1, |
| (tmp >> 23) & 0x1, (tmp >> 24) & 0x7, |
| (tmp >> 27) & 0x1, (tmp >> 28) & 0x1); |
| } |
| |
| /* Look for the SMBus device. */ |
| smbus_dev = pci_dev_find(0x1002, 0x4385); |
| |
| if (has_spi && !smbus_dev) { |
| fprintf(stderr, "ERROR: SMBus device not found. Not enabling SPI.\n"); |
| has_spi = 0; |
| } |
| if (has_spi) { |
| /* Note about the bit tests below: If a bit is zero, the GPIO is SPI. */ |
| /* GPIO11/SPI_DO and GPIO12/SPI_DI status */ |
| reg = pci_read_byte(smbus_dev, 0xAB); |
| reg &= 0xC0; |
| printf_debug("GPIO11 used for %s\n", (reg & (1 << 6)) ? "GPIO" : "SPI_DO"); |
| printf_debug("GPIO12 used for %s\n", (reg & (1 << 7)) ? "GPIO" : "SPI_DI"); |
| if (reg != 0x00) |
| has_spi = 0; |
| /* GPIO31/SPI_HOLD and GPIO32/SPI_CS status */ |
| reg = pci_read_byte(smbus_dev, 0x83); |
| reg &= 0xC0; |
| printf_debug("GPIO31 used for %s\n", (reg & (1 << 6)) ? "GPIO" : "SPI_HOLD"); |
| printf_debug("GPIO32 used for %s\n", (reg & (1 << 7)) ? "GPIO" : "SPI_CS"); |
| /* SPI_HOLD is not used on all boards, filter it out. */ |
| if ((reg & 0x80) != 0x00) |
| has_spi = 0; |
| /* GPIO47/SPI_CLK status */ |
| reg = pci_read_byte(smbus_dev, 0xA7); |
| reg &= 0x40; |
| printf_debug("GPIO47 used for %s\n", (reg & (1 << 6)) ? "GPIO" : "SPI_CLK"); |
| if (reg != 0x00) |
| has_spi = 0; |
| } |
| |
| buses_supported = CHIP_BUSTYPE_LPC | CHIP_BUSTYPE_FWH; |
| if (has_spi) { |
| buses_supported |= CHIP_BUSTYPE_SPI; |
| spi_controller = SPI_CONTROLLER_SB600; |
| } |
| |
| /* Read ROM strap override register. */ |
| OUTB(0x8f, 0xcd6); |
| reg = INB(0xcd7); |
| reg &= 0x0e; |
| printf_debug("ROM strap override is %sactive", (reg & 0x02) ? "" : "not "); |
| if (reg & 0x02) { |
| switch ((reg & 0x0c) >> 2) { |
| case 0x00: |
| printf_debug(": LPC"); |
| break; |
| case 0x01: |
| printf_debug(": PCI"); |
| break; |
| case 0x02: |
| printf_debug(": FWH"); |
| break; |
| case 0x03: |
| printf_debug(": SPI"); |
| break; |
| } |
| } |
| printf_debug("\n"); |
| |
| /* Force enable SPI ROM in SB600 PM register. |
| * If we enable SPI ROM here, we have to disable it after we leave. |
| * But how can we know which ROM we are going to handle? So we have |
| * to trade off. We only access LPC ROM if we boot via LPC ROM. And |
| * only SPI ROM if we boot via SPI ROM. If you want to access SPI on |
| * boards with LPC straps, you have to use the code below. |
| */ |
| /* |
| OUTB(0x8f, 0xcd6); |
| OUTB(0x0e, 0xcd7); |
| */ |
| |
| return 0; |
| } |
| |
| static int enable_flash_nvidia_nforce2(struct pci_dev *dev, const char *name) |
| { |
| uint8_t tmp; |
| |
| pci_write_byte(dev, 0x92, 0); |
| |
| tmp = pci_read_byte(dev, 0x6d); |
| tmp |= 0x01; |
| pci_write_byte(dev, 0x6d, tmp); |
| |
| return 0; |
| } |
| |
| static int enable_flash_ck804(struct pci_dev *dev, const char *name) |
| { |
| uint8_t old, new; |
| |
| old = pci_read_byte(dev, 0x88); |
| new = old | 0xc0; |
| if (new != old) { |
| pci_write_byte(dev, 0x88, new); |
| if (pci_read_byte(dev, 0x88) != new) { |
| printf_debug("tried to set 0x%x to 0x%x on %s failed (WARNING ONLY)\n", 0x88, new, name); |
| } |
| } |
| |
| old = pci_read_byte(dev, 0x6d); |
| new = old | 0x01; |
| if (new == old) |
| return 0; |
| pci_write_byte(dev, 0x6d, new); |
| |
| if (pci_read_byte(dev, 0x6d) != new) { |
| printf_debug("tried to set 0x%x to 0x%x on %s failed (WARNING ONLY)\n", 0x6d, new, name); |
| return -1; |
| } |
| |
| return 0; |
| } |
| |
| /* ATI Technologies Inc IXP SB400 PCI-ISA Bridge (rev 80) */ |
| static int enable_flash_sb400(struct pci_dev *dev, const char *name) |
| { |
| uint8_t tmp; |
| struct pci_dev *smbusdev; |
| |
| /* Look for the SMBus device. */ |
| smbusdev = pci_dev_find(0x1002, 0x4372); |
| |
| if (!smbusdev) { |
| fprintf(stderr, "ERROR: SMBus device not found. Aborting.\n"); |
| exit(1); |
| } |
| |
| /* Enable some SMBus stuff. */ |
| tmp = pci_read_byte(smbusdev, 0x79); |
| tmp |= 0x01; |
| pci_write_byte(smbusdev, 0x79, tmp); |
| |
| /* Change southbridge. */ |
| tmp = pci_read_byte(dev, 0x48); |
| tmp |= 0x21; |
| pci_write_byte(dev, 0x48, tmp); |
| |
| /* Now become a bit silly. */ |
| tmp = INB(0xc6f); |
| OUTB(tmp, 0xeb); |
| OUTB(tmp, 0xeb); |
| tmp |= 0x40; |
| OUTB(tmp, 0xc6f); |
| OUTB(tmp, 0xeb); |
| OUTB(tmp, 0xeb); |
| |
| return 0; |
| } |
| |
| static int enable_flash_mcp55(struct pci_dev *dev, const char *name) |
| { |
| uint8_t old, new, byte; |
| uint16_t word; |
| |
| /* Set the 0-16 MB enable bits. */ |
| byte = pci_read_byte(dev, 0x88); |
| byte |= 0xff; /* 256K */ |
| pci_write_byte(dev, 0x88, byte); |
| byte = pci_read_byte(dev, 0x8c); |
| byte |= 0xff; /* 1M */ |
| pci_write_byte(dev, 0x8c, byte); |
| word = pci_read_word(dev, 0x90); |
| word |= 0x7fff; /* 16M */ |
| pci_write_word(dev, 0x90, word); |
| |
| old = pci_read_byte(dev, 0x6d); |
| new = old | 0x01; |
| if (new == old) |
| return 0; |
| pci_write_byte(dev, 0x6d, new); |
| |
| if (pci_read_byte(dev, 0x6d) != new) { |
| printf_debug("tried to set 0x%x to 0x%x on %s failed (WARNING ONLY)\n", 0x6d, new, name); |
| return -1; |
| } |
| |
| return 0; |
| } |
| |
| static int enable_flash_ht1000(struct pci_dev *dev, const char *name) |
| { |
| uint8_t byte; |
| |
| /* Set the 4MB enable bit. */ |
| byte = pci_read_byte(dev, 0x41); |
| byte |= 0x0e; |
| pci_write_byte(dev, 0x41, byte); |
| |
| byte = pci_read_byte(dev, 0x43); |
| byte |= (1 << 4); |
| pci_write_byte(dev, 0x43, byte); |
| |
| return 0; |
| } |
| |
| /** |
| * Usually on the x86 architectures (and on other PC-like platforms like some |
| * Alphas or Itanium) the system flash is mapped right below 4G. On the AMD |
| * Elan SC520 only a small piece of the system flash is mapped there, but the |
| * complete flash is mapped somewhere below 1G. The position can be determined |
| * by the BOOTCS PAR register. |
| */ |
| static int get_flashbase_sc520(struct pci_dev *dev, const char *name) |
| { |
| int i, bootcs_found = 0; |
| uint32_t parx = 0; |
| void *mmcr; |
| |
| /* 1. Map MMCR */ |
| mmcr = physmap("Elan SC520 MMCR", 0xfffef000, getpagesize()); |
| |
| /* 2. Scan PAR0 (0x88) - PAR15 (0xc4) for |
| * BOOTCS region (PARx[31:29] = 100b)e |
| */ |
| for (i = 0x88; i <= 0xc4; i += 4) { |
| parx = mmio_readl(mmcr + i); |
| if ((parx >> 29) == 4) { |
| bootcs_found = 1; |
| break; /* BOOTCS found */ |
| } |
| } |
| |
| /* 3. PARx[25] = 1b --> flashbase[29:16] = PARx[13:0] |
| * PARx[25] = 0b --> flashbase[29:12] = PARx[17:0] |
| */ |
| if (bootcs_found) { |
| if (parx & (1 << 25)) { |
| parx &= (1 << 14) - 1; /* Mask [13:0] */ |
| flashbase = parx << 16; |
| } else { |
| parx &= (1 << 18) - 1; /* Mask [17:0] */ |
| flashbase = parx << 12; |
| } |
| } else { |
| printf("AMD Elan SC520 detected, but no BOOTCS. Assuming flash at 4G\n"); |
| } |
| |
| /* 4. Clean up */ |
| physunmap(mmcr, getpagesize()); |
| return 0; |
| } |
| |
| /* Please keep this list alphabetically sorted by vendor/device. */ |
| const struct penable chipset_enables[] = { |
| {0x10B9, 0x1533, OK, "ALi", "M1533", enable_flash_ali_m1533}, |
| {0x1022, 0x7440, OK, "AMD", "AMD-768", enable_flash_amd8111}, |
| {0x1022, 0x7468, OK, "AMD", "AMD8111", enable_flash_amd8111}, |
| {0x1078, 0x0100, OK, "AMD", "CS5530(A)", enable_flash_cs5530}, |
| {0x1022, 0x2080, OK, "AMD", "CS5536", enable_flash_cs5536}, |
| {0x1022, 0x3000, OK, "AMD", "Elan SC520", get_flashbase_sc520}, |
| {0x1002, 0x438D, OK, "AMD", "SB600", enable_flash_sb600}, |
| {0x1002, 0x439d, OK, "AMD", "SB700", enable_flash_sb600}, |
| {0x100b, 0x0510, NT, "AMD", "SC1100", enable_flash_sc1100}, |
| {0x1002, 0x4377, OK, "ATI", "SB400", enable_flash_sb400}, |
| {0x1166, 0x0205, OK, "Broadcom", "HT-1000", enable_flash_ht1000}, |
| {0x8086, 0x7198, OK, "Intel", "440MX", enable_flash_piix4}, |
| {0x8086, 0x25a1, OK, "Intel", "6300ESB", enable_flash_ich_4e}, |
| {0x8086, 0x2670, OK, "Intel", "631xESB/632xESB/3100", enable_flash_ich_dc}, |
| {0x8086, 0x5031, OK, "Intel", "EP80579", enable_flash_ich7}, |
| {0x8086, 0x2420, OK, "Intel", "ICH0", enable_flash_ich_4e}, |
| {0x8086, 0x3a18, OK, "Intel", "ICH10", enable_flash_ich10}, |
| {0x8086, 0x3a1a, OK, "Intel", "ICH10D", enable_flash_ich10}, |
| {0x8086, 0x3a14, OK, "Intel", "ICH10DO", enable_flash_ich10}, |
| {0x8086, 0x3a16, OK, "Intel", "ICH10R", enable_flash_ich10}, |
| {0x8086, 0x2440, OK, "Intel", "ICH2", enable_flash_ich_4e}, |
| {0x8086, 0x244c, OK, "Intel", "ICH2-M", enable_flash_ich_4e}, |
| {0x8086, 0x248c, OK, "Intel", "ICH3-M", enable_flash_ich_4e}, |
| {0x8086, 0x2480, OK, "Intel", "ICH3-S", enable_flash_ich_4e}, |
| {0x8086, 0x24c0, OK, "Intel", "ICH4/ICH4-L", enable_flash_ich_4e}, |
| {0x8086, 0x24cc, OK, "Intel", "ICH4-M", enable_flash_ich_4e}, |
| {0x8086, 0x24d0, OK, "Intel", "ICH5/ICH5R", enable_flash_ich_4e}, |
| {0x8086, 0x2640, OK, "Intel", "ICH6/ICH6R", enable_flash_ich_dc}, |
| {0x8086, 0x2641, OK, "Intel", "ICH6-M", enable_flash_ich_dc}, |
| {0x8086, 0x27b0, OK, "Intel", "ICH7DH", enable_flash_ich7}, |
| {0x8086, 0x27b8, OK, "Intel", "ICH7/ICH7R", enable_flash_ich7}, |
| {0x8086, 0x27b9, OK, "Intel", "ICH7M", enable_flash_ich7}, |
| {0x8086, 0x27bd, OK, "Intel", "ICH7MDH", enable_flash_ich7}, |
| {0x8086, 0x2410, OK, "Intel", "ICH", enable_flash_ich_4e}, |
| {0x8086, 0x2812, OK, "Intel", "ICH8DH", enable_flash_ich8}, |
| {0x8086, 0x2814, OK, "Intel", "ICH8DO", enable_flash_ich8}, |
| {0x8086, 0x2810, OK, "Intel", "ICH8/ICH8R", enable_flash_ich8}, |
| {0x8086, 0x2815, OK, "Intel", "ICH8M", enable_flash_ich8}, |
| {0x8086, 0x2811, OK, "Intel", "ICH8M-E", enable_flash_ich8}, |
| {0x8086, 0x2918, OK, "Intel", "ICH9", enable_flash_ich9}, |
| {0x8086, 0x2912, OK, "Intel", "ICH9DH", enable_flash_ich9}, |
| {0x8086, 0x2914, OK, "Intel", "ICH9DO", enable_flash_ich9}, |
| {0x8086, 0x2919, OK, "Intel", "ICH9M", enable_flash_ich9}, |
| {0x8086, 0x2917, OK, "Intel", "ICH9M-E", enable_flash_ich9}, |
| {0x8086, 0x2916, OK, "Intel", "ICH9R", enable_flash_ich9}, |
| {0x8086, 0x1234, NT, "Intel", "MPIIX", enable_flash_piix4}, |
| {0x8086, 0x7000, OK, "Intel", "PIIX3", enable_flash_piix4}, |
| {0x8086, 0x7110, OK, "Intel", "PIIX4/4E/4M", enable_flash_piix4}, |
| {0x8086, 0x122e, OK, "Intel", "PIIX", enable_flash_piix4}, |
| {0x10de, 0x0050, OK, "NVIDIA", "CK804", enable_flash_ck804}, /* LPC */ |
| {0x10de, 0x0051, OK, "NVIDIA", "CK804", enable_flash_ck804}, /* Pro */ |
| {0x10de, 0x0060, OK, "NVIDIA", "NForce2", enable_flash_nvidia_nforce2}, |
| /* Slave, should not be here, to fix known bug for A01. */ |
| {0x10de, 0x00d3, OK, "NVIDIA", "CK804", enable_flash_ck804}, |
| {0x10de, 0x0260, NT, "NVIDIA", "MCP51", enable_flash_ck804}, |
| {0x10de, 0x0261, NT, "NVIDIA", "MCP51", enable_flash_ck804}, |
| {0x10de, 0x0262, NT, "NVIDIA", "MCP51", enable_flash_ck804}, |
| {0x10de, 0x0263, NT, "NVIDIA", "MCP51", enable_flash_ck804}, |
| {0x10de, 0x0360, OK, "NVIDIA", "MCP55", enable_flash_mcp55}, /* M57SLI*/ |
| {0x10de, 0x0361, OK, "NVIDIA", "MCP55", enable_flash_mcp55}, /* LPC */ |
| {0x10de, 0x0362, OK, "NVIDIA", "MCP55", enable_flash_mcp55}, /* LPC */ |
| {0x10de, 0x0363, OK, "NVIDIA", "MCP55", enable_flash_mcp55}, /* LPC */ |
| {0x10de, 0x0364, OK, "NVIDIA", "MCP55", enable_flash_mcp55}, /* LPC */ |
| {0x10de, 0x0365, OK, "NVIDIA", "MCP55", enable_flash_mcp55}, /* LPC */ |
| {0x10de, 0x0366, OK, "NVIDIA", "MCP55", enable_flash_mcp55}, /* LPC */ |
| {0x10de, 0x0367, OK, "NVIDIA", "MCP55", enable_flash_mcp55}, /* Pro */ |
| {0x10de, 0x0548, OK, "NVIDIA", "MCP67", enable_flash_mcp55}, |
| {0x1039, 0x0008, OK, "SiS", "SiS5595", enable_flash_sis5595}, |
| {0x1039, 0x0630, NT, "SiS", "SiS630", enable_flash_sis630}, |
| {0x1106, 0x8324, OK, "VIA", "CX700", enable_flash_vt823x}, |
| {0x1106, 0x8231, NT, "VIA", "VT8231", enable_flash_vt823x}, |
| {0x1106, 0x3074, NT, "VIA", "VT8233", enable_flash_vt823x}, |
| {0x1106, 0x3177, OK, "VIA", "VT8235", enable_flash_vt823x}, |
| {0x1106, 0x3227, OK, "VIA", "VT8237", enable_flash_vt823x}, |
| {0x1106, 0x3337, OK, "VIA", "VT8237A", enable_flash_vt823x}, |
| {0x1106, 0x3372, OK, "VIA", "VT8237S", enable_flash_vt8237s_spi}, |
| {0x1106, 0x8353, OK, "VIA", "VX800", enable_flash_vt8237s_spi}, |
| {0x1106, 0x0586, OK, "VIA", "VT82C586A/B", enable_flash_amd8111}, |
| {0x1106, 0x0686, NT, "VIA", "VT82C686A/B", enable_flash_amd8111}, |
| |
| {}, |
| }; |
| |
| int chipset_flash_enable(void) |
| { |
| struct pci_dev *dev = 0; |
| int ret = -2; /* Nothing! */ |
| int i; |
| |
| /* Now let's try to find the chipset we have... */ |
| for (i = 0; chipset_enables[i].vendor_name != NULL; i++) { |
| dev = pci_dev_find(chipset_enables[i].vendor_id, |
| chipset_enables[i].device_id); |
| if (dev) |
| break; |
| } |
| |
| if (dev) { |
| printf("Found chipset \"%s %s\", enabling flash write... ", |
| chipset_enables[i].vendor_name, |
| chipset_enables[i].device_name); |
| |
| ret = chipset_enables[i].doit(dev, |
| chipset_enables[i].device_name); |
| if (ret) |
| printf("FAILED!\n"); |
| else |
| printf("OK.\n"); |
| } |
| printf("This chipset supports the following protocols: %s.\n", |
| flashbuses_to_text(buses_supported)); |
| |
| return ret; |
| } |