README - flashprog - Gitiles

 -------------------------------------------------------------------------------
 flashrom README
 -------------------------------------------------------------------------------

 flashrom is a utility for detecting, reading, writing, verifying and erasing
 flash chips. It is often used to flash BIOS/EFI/coreboot/firmware images
 in-system using a supported mainboard, but it also supports flashing of network
 cards (NICs), SATA controller cards, and other external devices which can
 program flash chips.

 It supports a wide range of DIP32, PLCC32, DIP8, SO8/SOIC8, TSOP32, and TSOP40
 chips, which use various protocols such as LPC, FWH, parallel flash, or SPI.

 Do not use flashrom on laptops! The embedded controller (EC) present in many
 laptops interacts badly with any flash attempts and can brick your laptop
 permanently.

 Please make a backup of your flash chip before writing to it.

 Please see the flashrom(8) manpage.


 Packaging
 ---------

 To package flashrom and remove dependencies on subversion, either use
 make export
 or
 make tarball

 make export will export all flashrom files from the subversion repository at
 revision BASE into a directory named $EXPORTDIR/flashrom-$VERSION-r$SVNREVISION
 and will additionally modify the Makefile in that directory to contain the svn
 revision of the exported tree.

 make tarball will simply tar up the result of make export and gzip compress it.

 The snapshot tarballs are the result of make tarball and require no further
 processing.


 Build Instructions
 ------------------

 To build flashrom you need to install the following packages or ports:

 Linux et al:

  * pciutils / libpci
  * pciutils-devel / pciutils-dev / libpci-dev
  * zlib-devel / zlib1g-dev (needed if libpci was compiled with libz support)

 On FreeBSD, you need the following ports:

  * devel/gmake
  * devel/libpci

 On OpenBSD, you need the following ports:

  * devel/gmake
  * sysutils/pciutils

 To compile on Linux, use:

  make

 To compile on FreeBSD, use:

  gmake

 To compile on Nexenta, use:

  make

 To compile on Solaris, use:

  gmake LDFLAGS="-L$pathtolibpci" CC="gcc -I$pathtopciheaders" CFLAGS=-O2

 To compile on NetBSD or DragonFly BSD, use:

  ln -s /usr/pkg/include/pciutils pci
  gmake CPPFLAGS=-I. LDFLAGS="-L/usr/pkg/lib -Wl,-rpath-link,/usr/pkg/lib"

 To compile on OpenBSD, use:

  gmake

 To compile and run on Darwin/Mac OS X:

  Install DirectHW from coresystems GmbH.
  DirectHW is available at http://www.coresystems.de/en/directhw .

 To cross-compile on Linux for DOS:

  Get RPMs of the cross compiler from the DJGPP site and install them:
  djcross-binutils-2.19.1-10ap.i386.rpm
  djcross-gcc-4.3.2-8ap.i686.rpm
  djcrx-2.04pre_20090725-13ap.i386.rpm
  Download pciutils 3.1.5 and apply http://assembler.cz/flashrom/pciutils.patch
  Download and compile http://assembler.cz/flashrom/libgetopt/
  Compile pciutils, see README.DJGPP for instructions.
  Enter the flashrom directory.
  ../libpci should contain pciutils source and binaries.
  ../libgetopt should contain getopt.a from libgetopt.
  Run either (change settings where appropriate)
  make CC=i586-pc-msdosdjgpp-gcc STRIP=i586-pc-msdosdjgpp-strip OS_ARCH=DOS
  or (above settings hardcoded)
  make djgpp-dos
  You might have to add WARNERROR=no to the make command line.
  To run flashrom.exe, download and unpack
  http://homer.rice.edu/~sandmann/cwsdpmi/csdpmi7b.zip and make sure
  CWSDPMI.EXE is in the current directory.

 Installation
 ------------

 In order to install flashrom and the manpage into /usr/local, type:

  make install

 For installation in a different directory use DESTDIR, e.g. like this:

  make DESTDIR=/usr install

 If you have insufficient permissions for the destination directory, use sudo
 by adding sudo in front of the commands above.


 Contact
 -------

 The official flashrom website is:

   http://www.flashrom.org/

 The IRC channel is

   #flashrom at irc.freenode.net

 The mailing list address is

   flashrom@flashrom.org
	-------------------------------------------------------------------------------
	flashrom README
	-------------------------------------------------------------------------------

	flashrom is a utility for detecting, reading, writing, verifying and erasing
	flash chips. It is often used to flash BIOS/EFI/coreboot/firmware images
	in-system using a supported mainboard, but it also supports flashing of network
	cards (NICs), SATA controller cards, and other external devices which can
	program flash chips.

	It supports a wide range of DIP32, PLCC32, DIP8, SO8/SOIC8, TSOP32, and TSOP40
	chips, which use various protocols such as LPC, FWH, parallel flash, or SPI.

	Do not use flashrom on laptops! The embedded controller (EC) present in many
	laptops interacts badly with any flash attempts and can brick your laptop
	permanently.

	Please make a backup of your flash chip before writing to it.

	Please see the flashrom(8) manpage.


	Packaging
	---------

	To package flashrom and remove dependencies on subversion, either use
	make export
	or
	make tarball

	make export will export all flashrom files from the subversion repository at
	revision BASE into a directory named $EXPORTDIR/flashrom-$VERSION-r$SVNREVISION
	and will additionally modify the Makefile in that directory to contain the svn
	revision of the exported tree.

	make tarball will simply tar up the result of make export and gzip compress it.

	The snapshot tarballs are the result of make tarball and require no further
	processing.


	Build Instructions
	------------------

	To build flashrom you need to install the following packages or ports:

	Linux et al:

	* pciutils / libpci
	* pciutils-devel / pciutils-dev / libpci-dev
	* zlib-devel / zlib1g-dev (needed if libpci was compiled with libz support)

	On FreeBSD, you need the following ports:

	* devel/gmake
	* devel/libpci

	On OpenBSD, you need the following ports:

	* devel/gmake
	* sysutils/pciutils

	To compile on Linux, use:

	make

	To compile on FreeBSD, use:

	gmake

	To compile on Nexenta, use:

	make

	To compile on Solaris, use:

	gmake LDFLAGS="-L$pathtolibpci" CC="gcc -I$pathtopciheaders" CFLAGS=-O2

	To compile on NetBSD or DragonFly BSD, use:

	ln -s /usr/pkg/include/pciutils pci
	gmake CPPFLAGS=-I. LDFLAGS="-L/usr/pkg/lib -Wl,-rpath-link,/usr/pkg/lib"

	To compile on OpenBSD, use:

	gmake

	To compile and run on Darwin/Mac OS X:

	Install DirectHW from coresystems GmbH.
	DirectHW is available at http://www.coresystems.de/en/directhw .

	To cross-compile on Linux for DOS:

	Get RPMs of the cross compiler from the DJGPP site and install them:
	djcross-binutils-2.19.1-10ap.i386.rpm
	djcross-gcc-4.3.2-8ap.i686.rpm
	djcrx-2.04pre_20090725-13ap.i386.rpm
	Download pciutils 3.1.5 and apply http://assembler.cz/flashrom/pciutils.patch
	Download and compile http://assembler.cz/flashrom/libgetopt/
	Compile pciutils, see README.DJGPP for instructions.
	Enter the flashrom directory.
	../libpci should contain pciutils source and binaries.
	../libgetopt should contain getopt.a from libgetopt.
	Run either (change settings where appropriate)
	make CC=i586-pc-msdosdjgpp-gcc STRIP=i586-pc-msdosdjgpp-strip OS_ARCH=DOS
	or (above settings hardcoded)
	make djgpp-dos
	You might have to add WARNERROR=no to the make command line.
	To run flashrom.exe, download and unpack
	http://homer.rice.edu/~sandmann/cwsdpmi/csdpmi7b.zip and make sure
	CWSDPMI.EXE is in the current directory.

	Installation
	------------

	In order to install flashrom and the manpage into /usr/local, type:

	make install

	For installation in a different directory use DESTDIR, e.g. like this:

	make DESTDIR=/usr install

	If you have insufficient permissions for the destination directory, use sudo
	by adding sudo in front of the commands above.


	Contact
	-------

	The official flashrom website is:

	http://www.flashrom.org/

	The IRC channel is

	#flashrom at irc.freenode.net

	The mailing list address is

	flashrom@flashrom.org