Add support for 3COM NICs as "external programmer" and Atmel AT49BV512
This allows flashrom to identify, read, write, erase and verify flash chips
on (some) 3COM network cards. The patch uses the external programmer
infrastructure, the network card is basically treated as an external
flash programmer.
Usage:
$ ./flashrom -p nic3com
flashrom v0.9.0-r498
Found NIC "3COM 3C905C: EtherLink 10/100 PCI (TX)" (10b7:9200), addr = 0xa400
Calibrating delay loop... OK.
Found chip "Atmel AT49BV512" (64 KB) at physical address 0xffff0000.
No operations were specified.
$ ./flashrom -p nic3com -E
flashrom v0.9.0-r498
Found NIC "3COM 3C905C: EtherLink 10/100 PCI (TX)" (10b7:9200), addr = 0xa400
Calibrating delay loop... OK.
Found chip "Atmel AT49BV512" (64 KB) at physical address 0xffff0000.
Erasing flash chip... SUCCESS.
$ ./flashrom -p nic3com -wv backup.bin
flashrom v0.9.0-r498
Found NIC "3COM 3C905C: EtherLink 10/100 PCI (TX)" (10b7:9200), addr = 0xa400
Calibrating delay loop... OK.
Found chip "Atmel AT49BV512" (64 KB) at physical address 0xffff0000.
Flash image seems to be a legacy BIOS. Disabling checks.
Programming page: 1023 at address: 0x0000ffc0
Verifying flash... VERIFIED.
$ ./flashrom -p nic3com -r backup.bin
flashrom v0.9.0-r498
Found NIC "3COM 3C905C: EtherLink 10/100 PCI (TX)" (10b7:9200), addr = 0xa400
Calibrating delay loop... OK.
Found chip "Atmel AT49BV512" (64 KB) at physical address 0xffff0000.
Reading flash... done.
I have tested this on actual hardware (see PCI IDs above) and all
operations worked fine.
Support for other 3COM cards will follow (I added some more which should
be supportable by this code, but they're untested so far), as well as
support for NICs from other vendors.
The patch also adds support for the Atmel AT49BV512 which is soldered
onto the 3COM NIC I used for testing.
Corresponding to flashrom svn r499.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Mateusz Murawski <matowy@tlen.pl>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
diff --git a/Makefile b/Makefile
index 45b8f94..b259a16 100644
--- a/Makefile
+++ b/Makefile
@@ -35,7 +35,7 @@
sst49lfxxxc.o sst_fwhub.o layout.o cbtable.o flashchips.o physmap.o \
flashrom.o w39v080fa.o sharplhf00l04.o w29ee011.o spi.o it87spi.o \
ichspi.o w39v040c.o sb600spi.o wbsio_spi.o m29f002.o internal.o \
- dummyflasher.o
+ dummyflasher.o nic3com.o
all: pciutils dep $(PROGRAM)
diff --git a/flash.h b/flash.h
index 2a11c24..a843b9d 100644
--- a/flash.h
+++ b/flash.h
@@ -79,6 +79,7 @@
extern int programmer;
#define PROGRAMMER_INTERNAL 0x00
#define PROGRAMMER_DUMMY 0x01
+#define PROGRAMMER_NIC3COM 0x02
struct programmer_entry {
const char *vendor;
@@ -281,6 +282,7 @@
#define AT_45DB321D 0x2701 /* Buggy data sheet */
#define AT_45DB642 /* No ID available */
#define AT_45DB642D 0x2800
+#define AT_49BV512 0x03
#define AT_49F002N 0x07 /* for AT49F002(N) */
#define AT_49F002NT 0x08 /* for AT49F002(N)T */
@@ -601,6 +603,18 @@
uint16_t dummy_chip_readw(const volatile void *addr);
uint32_t dummy_chip_readl(const volatile void *addr);
+/* nic3com.c */
+int nic3com_init(void);
+int nic3com_shutdown(void);
+void *nic3com_map(const char *descr, unsigned long phys_addr, size_t len);
+void nic3com_unmap(void *virt_addr, size_t len);
+void nic3com_chip_writeb(uint8_t val, volatile void *addr);
+void nic3com_chip_writew(uint16_t val, volatile void *addr);
+void nic3com_chip_writel(uint32_t val, volatile void *addr);
+uint8_t nic3com_chip_readb(const volatile void *addr);
+uint16_t nic3com_chip_readw(const volatile void *addr);
+uint32_t nic3com_chip_readl(const volatile void *addr);
+
/* flashrom.c */
extern int verbose;
#define printf_debug(x...) { if (verbose) printf(x); }
diff --git a/flashchips.c b/flashchips.c
index 6910c2c..bc203da 100644
--- a/flashchips.c
+++ b/flashchips.c
@@ -530,6 +530,20 @@
{
.vendor = "Atmel",
+ .name = "AT49BV512",
+ .manufacture_id = ATMEL_ID,
+ .model_id = AT_49BV512,
+ .total_size = 64,
+ .page_size = 64,
+ .tested = TEST_OK_PREW,
+ .probe = probe_jedec,
+ .erase = erase_chip_jedec,
+ .write = write_49f002,
+ .read = read_memmapped,
+ },
+
+ {
+ .vendor = "Atmel",
.name = "AT49F002(N)",
.manufacture_id = ATMEL_ID,
.model_id = AT_49F002N,
diff --git a/flashrom.8 b/flashrom.8
index 46a3742..7a48041 100644
--- a/flashrom.8
+++ b/flashrom.8
@@ -127,7 +127,9 @@
Specify the programmer device. Currently supported are:
.sp
.BR " internal" " (default, for in-system flashing in the mainboard)"
-
+.br
+.BR " nic3com" " (for flash ROMs on 3COM network cards)"
+.br
.BR " dummy" " (just prints all operations and accesses)"
.TP
.B "\-h, \-\-help"
diff --git a/flashrom.c b/flashrom.c
index f76722a..4e0e579 100644
--- a/flashrom.c
+++ b/flashrom.c
@@ -63,6 +63,19 @@
.chip_writel = dummy_chip_writel,
},
+ {
+ .init = nic3com_init,
+ .shutdown = nic3com_shutdown,
+ .map_flash_region = nic3com_map,
+ .unmap_flash_region = nic3com_unmap,
+ .chip_readb = nic3com_chip_readb,
+ .chip_readw = nic3com_chip_readw,
+ .chip_readl = nic3com_chip_readl,
+ .chip_writeb = nic3com_chip_writeb,
+ .chip_writew = nic3com_chip_writew,
+ .chip_writel = nic3com_chip_writel,
+ },
+
{},
};
@@ -439,6 +452,8 @@
programmer = PROGRAMMER_INTERNAL;
} else if (strncmp(optarg, "dummy", 5) == 0) {
programmer = PROGRAMMER_DUMMY;
+ } else if (strncmp(optarg, "nic3com", 7) == 0) {
+ programmer = PROGRAMMER_NIC3COM;
} else {
printf("Error: Unknown programmer.\n");
exit(1);
diff --git a/nic3com.c b/nic3com.c
new file mode 100644
index 0000000..9772731
--- /dev/null
+++ b/nic3com.c
@@ -0,0 +1,170 @@
+/*
+ * This file is part of the flashrom project.
+ *
+ * Copyright (C) 2009 Uwe Hermann <uwe@hermann-uwe.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <stdlib.h>
+#include <string.h>
+#include <errno.h>
+#include <sys/io.h>
+#include <pci/pci.h>
+#include "flash.h"
+
+#define BIOS_ROM_ADDR 0x04
+#define BIOS_ROM_DATA 0x08
+#define INT_STATUS 0x0e
+#define SELECT_REG_WINDOW 0x800
+
+#define PCI_IO_BASE_ADDRESS 0x10
+
+#define PCI_VENDOR_ID_3COM 0x10b7
+
+uint32_t io_base_addr;
+struct pci_access *pacc;
+
+#define OK 0
+#define NT 1 /* Not tested */
+
+static struct nic_status {
+ uint16_t device_id;
+ int status;
+ const char *device_name;
+} nics[] = {
+ /* 3C90xB */
+ {0x9055, NT, "3C90xB: PCI 10/100 Mbps; shared 10BASE-T/100BASE-TX"},
+ {0x9001, NT, "3C90xB: PCI 10/100 Mbps; shared 10BASE-T/100BASE-T4" },
+ {0x9004, NT, "3C90xB: PCI 10BASE-T (TPO)" },
+ {0x9005, NT, "3C90xB: PCI 10BASE-T/10BASE2/AUI (COMBO)" },
+ {0x9006, NT, "3C90xB: PCI 10BASE-T/10BASE2 (TPC)" },
+ {0x900a, NT, "3C90xB: PCI 10BASE-FL" },
+ {0x905a, NT, "3C90xB: PCI 10BASE-FX" },
+
+ /* 3C905C */
+ {0x9200, OK, "3C905C: EtherLink 10/100 PCI (TX)" },
+
+ /* 3C980C */
+ {0x9805, NT, "3C980C: EtherLink Server 10/100 PCI (TX)" },
+
+ {},
+};
+
+int nic3com_init(void)
+{
+ int i, found = 0;
+ struct pci_dev *dev;
+
+#if defined (__sun) && (defined(__i386) || defined(__amd64))
+ if (sysi86(SI86V86, V86SC_IOPL, PS_IOPL) != 0) {
+#elif defined(__FreeBSD__) || defined (__DragonFly__)
+ if ((io_fd = open("/dev/io", O_RDWR)) < 0) {
+#else
+ if (iopl(3) != 0) {
+#endif
+ fprintf(stderr, "ERROR: Could not get IO privileges (%s).\n"
+ "You need to be root.\n", strerror(errno));
+ exit(1);
+ }
+
+ pacc = pci_alloc(); /* Get the pci_access structure */
+ pci_init(pacc); /* Initialize the PCI library */
+ pci_scan_bus(pacc); /* We want to get the list of devices */
+
+ for (i = 0; nics[i].device_name != NULL; i++) {
+ dev = pci_dev_find(PCI_VENDOR_ID_3COM, nics[i].device_id);
+ if (!dev)
+ continue;
+
+ io_base_addr = pci_read_long(dev, PCI_IO_BASE_ADDRESS) & ~0x03;
+
+ printf("Found NIC \"3COM %s\" (%04x:%04x), addr = 0x%x\n",
+ nics[i].device_name, PCI_VENDOR_ID_3COM,
+ nics[i].device_id, io_base_addr);
+
+ if (nics[i].status == NT) {
+ printf("===\nThis NIC is UNTESTED. Please email a "
+ "report including the 'flashrom -p nic3com'\n"
+ "output to flashrom@coreboot.org if it works "
+ "for you. Thank you for your help!\n===\n");
+ }
+
+ found = 1;
+ break;
+ }
+
+ if (!found) {
+ fprintf(stderr, "Error: No supported 3COM NIC found.\n");
+ exit(1);
+ }
+
+ /*
+ * The lowest 16 bytes of the I/O mapped register space of (most) 3COM
+ * cards form a 'register window' into one of multiple (usually 8)
+ * register banks. For 3C90xB/3C90xC we need register window/bank 0.
+ */
+ OUTW(SELECT_REG_WINDOW + 0, io_base_addr + INT_STATUS);
+
+ return 0;
+}
+
+int nic3com_shutdown(void)
+{
+ return 0;
+}
+
+void *nic3com_map(const char *descr, unsigned long phys_addr, size_t len)
+{
+ return 0;
+}
+
+void nic3com_unmap(void *virt_addr, size_t len)
+{
+}
+
+void nic3com_chip_writeb(uint8_t val, volatile void *addr)
+{
+ OUTL((uint32_t)addr, io_base_addr + BIOS_ROM_ADDR);
+ OUTB(val, io_base_addr + BIOS_ROM_DATA);
+}
+
+void nic3com_chip_writew(uint16_t val, volatile void *addr)
+{
+}
+
+void nic3com_chip_writel(uint32_t val, volatile void *addr)
+{
+}
+
+uint8_t nic3com_chip_readb(const volatile void *addr)
+{
+ uint8_t val;
+
+ OUTL((uint32_t)addr, io_base_addr + BIOS_ROM_ADDR);
+ val = INB(io_base_addr + BIOS_ROM_DATA);
+
+ return val;
+}
+
+uint16_t nic3com_chip_readw(const volatile void *addr)
+{
+ return 0xffff;
+}
+
+uint32_t nic3com_chip_readl(const volatile void *addr)
+{
+ return 0xffffffff;
+}