nicintel_eeprom: Support for I210 emulated EEprom
On the I210 family there is no MAC EEprom, instead there is a big flash
(typically around 16Mb) with contents of the old MAC plus other stuff.
There is an interface to program the whole flash, but once it is
programmed it enters a "Secure Mode" that disables the interface.
Luckily, the section with the MAC can still be updated via the EEprom
interface. This patch adds support for this interface.
root@qt5022-fglrx:~# ./flashrom -p nicintel_eeprom:pci=01:0.0 -w kk.raw -V
flashrom v0.9.9-unknown on Linux 4.10.0-qtec-standard (x86_64)
flashrom is free software, get the source code at https://flashrom.org
flashrom was built with libpci 3.4.1, GCC 5.3.0, little endian
Command line (5 args): ./flashrom -p nicintel_eeprom:pci=01:0.0 -w kk.raw -V
Calibrating delay loop... OS timer resolution is 1 usecs, 1856M loops per second, 10 myus = 10 us,
100 myus = 102 us, 1000 myus = 1017 us, 10000 myus = 10044 us, 4 myus = 4 us, OK.
Initializing nicintel_eeprom programmer
Found "Intel I210 Gigabit Network Connection" (8086:1533, BDF 01:00.0).
Requested BAR is of type MEM, 32bit, not prefetchable
Requested BAR is of type MEM, 32bit, not prefetchable
The following protocols are supported: Programmer-specific.
Probing for Programmer Opaque flash chip, 0 kB: Found Programmer flash chip "Opaque flash chip"
(4 kB, Programmer-specific) on nicintel_eeprom.
Found Programmer flash chip "Opaque flash chip" (4 kB, Programmer-specific).
Reading old flash chip contents... done.
Erasing and writing flash chip... Trying erase function 0... 0x000000-0x000fff:W
Erase/write done.
Verifying flash... VERIFIED.
Change-Id: I553f33e5dcb4412d682fc93095b29bcfed11713c
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-on: https://review.coreboot.org/21431
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
diff --git a/nicintel_eeprom.c b/nicintel_eeprom.c
index b5d4202..e2fb584 100644
--- a/nicintel_eeprom.c
+++ b/nicintel_eeprom.c
@@ -25,6 +25,12 @@
* 4.7: Access to shared resources (FIXME: we should probably use this semaphore interface)
* 7.4: Register Descriptions
*/
+/*
+ * Datasheet: Intel Ethernet Controller I210: Datasheet
+ * 8.4.3: EEPROM-Mode Read Register
+ * 8.4.6: EEPROM-Mode Write Register
+ * Write process inspired on kernel e1000_i210.c
+ */
#include <stdlib.h>
#include <unistd.h>
@@ -34,10 +40,11 @@
#include "hwaccess.h"
#define PCI_VENDOR_ID_INTEL 0x8086
-#define MEMMAP_SIZE (0x14 + 3) /* Only EEC and EERD are needed. */
+#define MEMMAP_SIZE 0x1c /* Only EEC, EERD and EEWR are needed. */
#define EEC 0x10 /* EEPROM/Flash Control Register */
#define EERD 0x14 /* EEPROM Read Register */
+#define EEWR 0x18 /* EEPROM Write Register */
/* EPROM/Flash Control Register bits */
#define EE_SCK 0
@@ -49,6 +56,8 @@
#define EE_PRES 8
#define EE_SIZE 11
#define EE_SIZE_MASK 0xf
+#define EE_FLUPD 23
+#define EE_FLUDONE 26
/* EEPROM Read Register bits */
#define EERD_START 0
@@ -56,11 +65,18 @@
#define EERD_ADDR 2
#define EERD_DATA 16
+/* EEPROM Write Register bits */
+#define EEWR_CMDV 0
+#define EEWR_DONE 1
+#define EEWR_ADDR 2
+#define EEWR_DATA 16
+
#define BIT(x) (1<<x)
#define EE_PAGE_MASK 0x3f
static uint8_t *nicintel_eebar;
static struct pci_dev *nicintel_pci;
+static bool done_i20_write = false;
#define UNPROG_DEVICE 0x1509
@@ -71,10 +87,35 @@
{PCI_VENDOR_ID_INTEL, 0x1511, NT , "Intel", "82580 Quad Gigabit Ethernet Controller (Ext. PHY)"},
{PCI_VENDOR_ID_INTEL, 0x1511, NT , "Intel", "82580 Dual Gigabit Ethernet Controller (Copper)"},
{PCI_VENDOR_ID_INTEL, UNPROG_DEVICE, OK, "Intel", "Unprogrammed 82580 Quad/Dual Gigabit Ethernet Controller"},
+ {PCI_VENDOR_ID_INTEL, 0x1531, NT, "Intel", "I210 Gigabit Network Connection Unprogrammed"},
+ {PCI_VENDOR_ID_INTEL, 0x1532, NT, "Intel", "I211 Gigabit Network Connection Unprogrammed"},
+ {PCI_VENDOR_ID_INTEL, 0x1533, OK, "Intel", "I210 Gigabit Network Connection"},
+ {PCI_VENDOR_ID_INTEL, 0x1536, NT, "Intel", "I210 Gigabit Network Connection SERDES Fiber"},
+ {PCI_VENDOR_ID_INTEL, 0x1537, NT, "Intel", "I210 Gigabit Network Connection SERDES Backplane"},
+ {PCI_VENDOR_ID_INTEL, 0x1538, NT, "Intel", "I210 Gigabit Network Connection SGMII"},
+ {PCI_VENDOR_ID_INTEL, 0x1539, NT, "Intel", "I211 Gigabit Network Connection"},
{0},
};
-static int nicintel_ee_probe(struct flashctx *flash)
+static inline bool is_i210(uint16_t device_id)
+{
+ return (device_id & 0xff00) == 0x1500;
+}
+
+static int nicintel_ee_probe_i210(struct flashctx *flash)
+{
+ /* Emulated eeprom has a fixed size of 4 KB */
+ flash->chip->total_size = 4;
+ flash->chip->page_size = flash->chip->total_size * 1024;
+ flash->chip->tested = TEST_OK_PREW;
+ flash->chip->gran = write_gran_1byte_implicit_erase;
+ flash->chip->block_erasers->eraseblocks[0].size = flash->chip->page_size;
+ flash->chip->block_erasers->eraseblocks[0].count = 1;
+
+ return 1;
+}
+
+static int nicintel_ee_probe_82580(struct flashctx *flash)
{
if (nicintel_pci->device_id == UNPROG_DEVICE)
flash->chip->total_size = 16; /* Fall back to minimum supported size. */
@@ -103,6 +144,15 @@
return 1;
}
+static int nicintel_ee_probe(struct flashctx *flash)
+{
+ if (is_i210(nicintel_pci->device_id))
+ return nicintel_ee_probe_i210(flash);
+
+ return nicintel_ee_probe_82580(flash);
+}
+
+#define MAX_ATTEMPTS 10000000
static int nicintel_ee_read_word(unsigned int addr, uint16_t *data)
{
uint32_t tmp = BIT(EERD_START) | (addr << EERD_ADDR);
@@ -110,7 +160,7 @@
/* Poll done flag. 10.000.000 cycles seem to be enough. */
uint32_t i;
- for (i = 0; i < 10000000; i++) {
+ for (i = 0; i < MAX_ATTEMPTS; i++) {
tmp = pci_mmio_readl(nicintel_eebar + EERD);
if (tmp & BIT(EERD_DONE)) {
*data = (tmp >> EERD_DATA) & 0xffff;
@@ -151,6 +201,83 @@
return 0;
}
+static int nicintel_ee_write_word_i210(unsigned int addr, uint16_t data)
+{
+ uint32_t eewr;
+
+ eewr = addr << EEWR_ADDR;
+ eewr |= data << EEWR_DATA;
+ eewr |= BIT(EEWR_CMDV);
+ pci_mmio_writel(eewr, nicintel_eebar + EEWR);
+
+ programmer_delay(5);
+ for (int i = 0; i < MAX_ATTEMPTS; i++)
+ if (pci_mmio_readl(nicintel_eebar + EEWR) & BIT(EEWR_DONE))
+ return 0;
+ return -1;
+}
+
+static int nicintel_ee_write_i210(struct flashctx *flash, const uint8_t *buf, unsigned int addr, unsigned int len)
+{
+ done_i20_write = true;
+
+ if (addr & 1) {
+ uint16_t data;
+
+ if (nicintel_ee_read_word(addr / 2, &data)) {
+ msg_perr("Timeout reading heading byte\n");
+ return -1;
+ }
+
+ data &= 0xff;
+ data |= (buf ? (buf[0]) : 0xff) << 8;
+
+ if (nicintel_ee_write_word_i210(addr / 2, data)) {
+ msg_perr("Timeout writing heading word\n");
+ return -1;
+ }
+
+ if (buf)
+ buf ++;
+ addr ++;
+ len --;
+ }
+
+ while (len > 0) {
+ uint16_t data;
+
+ if (len == 1) {
+ if (nicintel_ee_read_word(addr / 2, &data)) {
+ msg_perr("Timeout reading tail byte\n");
+ return -1;
+ }
+
+ data &= 0xff00;
+ data |= buf ? (buf[0]) : 0xff;
+ } else {
+ if (buf)
+ data = buf[0] | (buf[1] << 8);
+ else
+ data = 0xffff;
+ }
+
+ if (nicintel_ee_write_word_i210(addr / 2, data)) {
+ msg_perr("Timeout writing Shadow RAM\n");
+ return -1;
+ }
+
+ if (buf)
+ buf += 2;
+ if (len > 2)
+ len -= 2;
+ else
+ len = 0;
+ addr += 2;
+ }
+
+ return 0;
+}
+
static int nicintel_ee_bitset(int reg, int bit, bool val)
{
uint32_t tmp;
@@ -224,7 +351,7 @@
return 0;
}
-static int nicintel_ee_write(struct flashctx *flash, const uint8_t *buf, unsigned int addr, unsigned int len)
+static int nicintel_ee_write_82580(struct flashctx *flash, const uint8_t *buf, unsigned int addr, unsigned int len)
{
if (nicintel_ee_req())
return -1;
@@ -262,6 +389,13 @@
nicintel_ee_bitset(EEC, EE_REQ, 0); /* Give up direct access. */
return ret;
}
+static int nicintel_ee_write(struct flashctx *flash, const uint8_t *buf, unsigned int addr, unsigned int len)
+{
+ if (is_i210(nicintel_pci->device_id))
+ return nicintel_ee_write_i210(flash, buf, addr, len);
+
+ return nicintel_ee_write_82580(flash, buf, addr, len);
+}
static int nicintel_ee_erase(struct flashctx *flash, unsigned int addr, unsigned int len)
{
@@ -275,6 +409,25 @@
.erase = nicintel_ee_erase,
};
+static int nicintel_ee_shutdown_i210(void *arg)
+{
+ if (!done_i20_write)
+ return 0;
+
+ uint32_t flup = pci_mmio_readl(nicintel_eebar + EEC);
+
+ flup |= BIT(EE_FLUPD);
+ pci_mmio_writel(flup, nicintel_eebar + EEC);
+
+ for (int i = 0; i < MAX_ATTEMPTS; i++)
+ if (pci_mmio_readl(nicintel_eebar + EEC) & BIT(EE_FLUDONE))
+ return 0;
+
+ msg_perr("Flash update failed\n");
+
+ return -1;
+}
+
static int nicintel_ee_shutdown(void *eecp)
{
uint32_t old_eec = *(uint32_t *)eecp;
@@ -306,9 +459,14 @@
if (!io_base_addr)
return 1;
- nicintel_eebar = rphysmap("Intel Gigabit NIC w/ SPI EEPROM", io_base_addr, MEMMAP_SIZE);
+ nicintel_eebar = rphysmap("Intel Gigabit NIC w/ SPI EEPROM",
+ io_base_addr + (is_i210(dev->device_id) ? 0x12000 : 0), MEMMAP_SIZE);
+ if (!nicintel_eebar)
+ return 1;
+
nicintel_pci = dev;
- if (dev->device_id != UNPROG_DEVICE) {
+ if ((dev->device_id != UNPROG_DEVICE) && ! is_i210(dev->device_id))
+ {
uint32_t eec = pci_mmio_readl(nicintel_eebar + EEC);
/* C.f. 3.3.1.5 for the detection mechanism (maybe? contradicting the EE_PRES definition),
@@ -327,5 +485,9 @@
return 1;
}
+ if (is_i210(dev->device_id))
+ if (register_shutdown(nicintel_ee_shutdown_i210, NULL))
+ return 1;
+
return register_opaque_master(&opaque_master_nicintel_ee);
}