Add support for the Open Graphics Project development card, OGD1, as a SPI flash programmer
The project is in the the process of designing and making a complete,
open source, graphics card. More info at http://wiki.opengraphics.org.
The first development card is a PCI add in card containing a couple of
FPGAs and a couple of serial flash chips (amongst other things). The
FPGAs are called XP10 and S3 (their part numbers). The XP10 contains its
own flash and does not need to be programmed by flashrom - it ensures
that the device can enumerate on the PCI bus without needing further
configuration.
The larger FPGA is the S3. This is configured from a large SPI flash
(2 MBytes). The second SPI flash is used to store the VGA BIOS. It is
smaller (128 KBytes). This patch adds support for programming either of
the two SPI flash chips.
The programmer device takes one configuration option which selects which
of the two flash chips is accessed. This must be set to either "cprom"
or "bprom". (The project refers to the two chips as "cprom" / "bprom",
"s3" and "bios" are more readable alternatives).
Add support for SST SST25VF010 (REMS). Mark SST SST25VF016B as tested
for write.
Corresponding to flashrom svn r1241.
Signed-off-by: Mark Marshall <mark.marshall@csr.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
diff --git a/flashrom.8 b/flashrom.8
index 0f2a6c4..6adb0ef 100644
--- a/flashrom.8
+++ b/flashrom.8
@@ -198,6 +198,9 @@
.BR "* nicintel_spi" " (for SPI flash ROMs attached to an Intel Gigabit \
network cards)"
.sp
+.BR "* ogp_spi" " (for SPI flash ROMs attached to an Open Graphics Project \
+graphics card)"
+.sp
Some programmers have optional or mandatory parameters which are described
in detail in the
.B PROGRAMMER SPECIFIC INFO
@@ -432,6 +435,34 @@
.sp
More information about the hardware is available at
http://rayer.ic.cz/elektro/spipgm.htm
+.TP
+.BR "ogp_spi " programmer
+The FLASH ROM chip to access must be specified with the
+.B rom
+parameter.
+.sp
+.B " flashrom \-p ogp_spi:rom=name"
+.sp
+Where
+.B name
+is either
+.B cprom
+or
+.B s3
+for the configuration ROM and
+.B bprom
+or
+.B bios
+for the BIOS ROM. If more than one card supported by the ogp_spi programmer
+is installed in your system, you have to specify the PCI address of the card
+you want to use with the
+.B pci=
+parameter as explained in the
+.B nic3com
+section above.
+.sp
+More information about the hardware is available at
+http://wiki.opengraphics.org
.SH EXIT STATUS
flashrom exits with 0 on success, 1 on most failures but with 2 if /dev/mem
(/dev/xsvc on Solaris) can not be opened and with 3 if a call to mmap() fails.
@@ -480,6 +511,9 @@
can be run as normal user on most operating systems if appropriate device
permissions are set.
.sp
+.B ogp
+needs PCI configuration space read access and raw memory access.
+.sp
On OpenBSD, you can obtain raw access permission by setting
securelevel=-1 in /etc/rc.securelevel and rebooting, or rebooting into single
user mode.
@@ -538,6 +572,8 @@
.br
Li-Ta Lo
.br
+Mark Marshall
+.br
Markus Boas
.br
Mattias Mattsson