Some cosmetics in README and manpage
Also, move more stuff to the manpage where it belongs (this also
eliminates some duplicated contents).
Corresponding to flashrom svn r460.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
diff --git a/README b/README
index 95397b2..d72f225 100644
--- a/README
+++ b/README
@@ -3,7 +3,7 @@
-------------------------------------------------------------------------------
flashrom is a utility for reading, writing, verifying and erasing flash ROM
-chips. It's often used to flash BIOS/coreboot/firmware images.
+chips. It's often used to flash BIOS/coreboot/firmware images.
It supports a wide range of DIP32, PLCC32, DIP8, SO8/SOIC8, TSOP32, and
TSOP40 chips, which use various protocols such as LPC, FWH, parallel flash,
@@ -15,31 +15,41 @@
Build Requirements
------------------
-To build the flashrom utility you need to install the following packages or
-ports:
+To build flashrom you need to install the following packages or ports:
Linux et al:
-* pciutils
-* pciutils-devel / pciutils-dev / libpci-dev
-* zlib-devel / zlib1g-dev
+
+ * pciutils
+ * pciutils-devel / pciutils-dev / libpci-dev
+ * zlib-devel / zlib1g-dev
On FreeBSD, you need the following ports:
-* devel/gmake
-* devel/libpci
-To compile on FreeBSD, use the command below:
-gmake
+ * devel/gmake
+ * devel/libpci
-To compile on Solaris, use the commands below:
-gmake LDFLAGS="-L$pathtolibpci -lpci -lz" CC="gcc -I$pathtopciheaders" CFLAGS=-O2
+To compile on Linux, use:
-To compile on DragonFly BSD, use the commands below:
-ln -s /usr/pkg/include/pciutils pci
-gmake CFLAGS=-I. LDFLAGS="-L/usr/pkg/lib -lpci -lz"
+ make
+
+To compile on FreeBSD, use:
+
+ gmake
+
+To compile on Solaris, use:
+
+ gmake LDFLAGS="-L$pathtolibpci -lpci -lz" CC="gcc -I$pathtopciheaders" \
+ CFLAGS=-O2
+
+To compile on DragonFly BSD, use:
+
+ ln -s /usr/pkg/include/pciutils pci
+ gmake CFLAGS=-I. LDFLAGS="-L/usr/pkg/lib -lpci -lz"
To compile and run on Darwin/Mac OS X:
-Install DirectIO from coresystems GmbH.
-DirectIO is available at http://www.coresystems.de/en/directio
+
+ Install DirectIO from coresystems GmbH.
+ DirectIO is available at http://www.coresystems.de/en/directio.
Usage / Options
@@ -51,52 +61,19 @@
Exit status
-----------
-flashrom exits with 0 on success, 1 on most failures but with 2 if /dev/mem
-(/dev/xsvc on Solaris) can not be opened and with 3 if a call to mmap() fails.
+Please see the flashrom(8) manpage.
coreboot Table and Mainboard Identification
--------------------------------------------
-flashrom reads the coreboot table to determine the current mainboard. If no
-coreboot table could be read or if you want to override these values, you can
-specify -m, e.g.:
-
- $ flashrom -w --mainboard AGAMI:ARUMA agami_aruma.rom
-
-See the 'Supported mainboards' section in the output of 'flashrom -L' for
-a list of boards which require the specification of the board name, if no
-coreboot table is found.
+Please see the flashrom(8) manpage.
ROM Layout Support
------------------
-flashrom supports ROM layouts. This allows you to flash certain parts of
-the flash chip only. A ROM layout file looks like follows:
-
- 00000000:00008fff gfxrom
- 00009000:0003ffff normal
- 00040000:0007ffff fallback
-
- i.e.:
- startaddr:endaddr name
-
- All addresses are offsets within the file, not absolute addresses!
-
-If you only want to update the normal image in a ROM you can say:
-
- flashrom -w --layout rom.layout --image normal agami_aruma.rom
-
-To update normal and fallback but leave the VGA BIOS alone, say:
-
- flashrom -w -l rom.layout -i normal -i fallback agami_aruma.rom
-
-Currently overlapping sections are not supported.
-
-ROM layouts should replace the -s and -e option since they are more
-flexible and they should lead to a ROM update file format with the
-ROM layout and the ROM image in one file (cpio, zip or something?).
+Please see the flashrom(8) manpage.
Supported Flash Chips / Chipsets / Mainboards