Fix timing of SPI status register writes (WRSR)
SPI write status register (WRSR) may take longer than 100 ms, and it
makes sense to poll for completion in 10 ms steps until 5 s are over.
This patch complements r1115.
Corresponding to flashrom svn r1201.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Joshua Roys <roysjosh@gmail.com>
diff --git a/flash.h b/flash.h
index 40382f0..9566af9 100644
--- a/flash.h
+++ b/flash.h
@@ -35,6 +35,9 @@
#define ERROR_PTR ((void*)-1)
+/* Error codes */
+#define TIMEOUT_ERROR -101
+
typedef unsigned long chipaddr;
int register_shutdown(void (*function) (void *data), void *data);
diff --git a/spi25.c b/spi25.c
index 688a329..9aaefc4 100644
--- a/spi25.c
+++ b/spi25.c
@@ -856,6 +856,7 @@
static int spi_write_status_register_ewsr(struct flashchip *flash, int status)
{
int result;
+ int i = 0;
struct spi_command cmds[] = {
{
/* WRSR requires either EWSR or WREN depending on chip type. */
@@ -879,15 +880,31 @@
if (result) {
msg_cerr("%s failed during command execution\n",
__func__);
+ /* No point in waiting for the command to complete if execution
+ * failed.
+ */
+ return result;
}
- /* WRSR performs a self-timed erase before the changes take effect. */
+ /* WRSR performs a self-timed erase before the changes take effect.
+ * This may take 50-85 ms in most cases, and some chips apparently
+ * allow running RDSR only once. Therefore pick an initial delay of
+ * 100 ms, then wait in 10 ms steps until a total of 5 s have elapsed.
+ */
programmer_delay(100 * 1000);
- return result;
+ while (spi_read_status_register() & JEDEC_RDSR_BIT_WIP) {
+ if (++i > 490) {
+ msg_cerr("Error: WIP bit after WRSR never cleared\n");
+ return TIMEOUT_ERROR;
+ }
+ programmer_delay(10 * 1000);
+ }
+ return 0;
}
static int spi_write_status_register_wren(struct flashchip *flash, int status)
{
int result;
+ int i = 0;
struct spi_command cmds[] = {
{
/* WRSR requires either EWSR or WREN depending on chip type. */
@@ -911,10 +928,25 @@
if (result) {
msg_cerr("%s failed during command execution\n",
__func__);
+ /* No point in waiting for the command to complete if execution
+ * failed.
+ */
+ return result;
}
- /* WRSR performs a self-timed erase before the changes take effect. */
+ /* WRSR performs a self-timed erase before the changes take effect.
+ * This may take 50-85 ms in most cases, and some chips apparently
+ * allow running RDSR only once. Therefore pick an initial delay of
+ * 100 ms, then wait in 10 ms steps until a total of 5 s have elapsed.
+ */
programmer_delay(100 * 1000);
- return result;
+ while (spi_read_status_register() & JEDEC_RDSR_BIT_WIP) {
+ if (++i > 490) {
+ msg_cerr("Error: WIP bit after WRSR never cleared\n");
+ return TIMEOUT_ERROR;
+ }
+ programmer_delay(10 * 1000);
+ }
+ return 0;
}
static int spi_write_status_register(struct flashchip *flash, int status)